25
Playback Zoom
To magnify the recorded image up to 10X at any
time during playback. Make sure that the TBC
mode is activated.
1)
Press PLAY
T
to find the scene of interest.
2)
Press ZOOM (
T/W
)
R
. Pressing
T
zooms in. To
end zoom press and hold
W
until magnification
returns to normal. Or, press STOP
U
and then
press PLAY
T
.
• Due to digital image processing, the quality of the
image may suffer.
Animation And Time-Lapse
The remote control lets you set/release interval
time and recording time without setting REC TIME/
INT. TIME (
pg. 21) in SYSTEM MENU.
Animation
Each time ANIM.
O
is pressed, the recording time
changes in the following order: 1/4S, 1/2S, 1S, 5S
and no indication (off).
Time-Lapse
Each time REC TIME
O
is pressed, the recording
time changes in the following order: 1/4S, 1/2S,
1S, 5S and no indication (off). Each time INT. TIME
f
is pressed, the interval time changes in the
following order: 15S, 30S, 1MIN, 5MIN and no
indication (off).
Insert Editing
You can record a new scene onto a previously
recorded tape. Only the video signal is recorded in
this mode.
1)
Set the Power Switch
@
to “
”.
2)
Play back the tape, locate the edit-out point and
press PAUSE
s
.
Press and hold COUNTER R/M
)
for more than 1 second to reset the tape
counter, then press it again for less than 1
second so that “M” appears.
3)
Press REW
Y
to go a little beyond the beginning
of the scene you want to replace, press PLAY
T
to view the recorded tape, and press PAUSE
s
exactly at the edit-in point where the new scene
should start.
4)
While holding down INSERT
I
, press and
release PAUSE
s
.
w
appears.
5)
To begin Insert Editing, press START/STOP
P
.
When the counter reaches “0:00:00”, editing
stops automatically and the camcorder enters
the Insert-Pause mode. To end Insert Editing,
press STOP
U
.
• During Insert Editing, the original audio will be
heard from the speaker.
• After step
4)
, “Retake” (
pg. 13) can be
performed.
• The tape may stop slightly before or after the
designated end point, and noise bars may appear.
Neither indicates a defect in the unit.
Audio Dubbing
You can record a new soundtrack on a prere-
corded tape (normal audio only). The sound is
recorded from the built-in microphone.
Perform steps
1)
and
2)
of the Insert Editing
procedure.
3)
Press REW
Y
to go a little beyond the beginning
of the scene onto which you want to dub the new
audio, press PLAY
T
to view the recorded tape,
then press PAUSE
s
at exactly the point where
dubbing should start.
4)
While holding down A. DUB
d
, press and
release PAUSE
s
.
5)
To begin Audio Dubbing, press PLAY
T
. When
the counter reaches “0:00:00”, Audio Dubbing
stops automatically and the camcorder enters
the Audio Dub-Standby mode. To end Audio
Dubbing, press STOP
U
.
• Do not press REW
Y
or FF
a
during Audio Dub-
Standby, or the edit points will not be accurate.
• If the microphone is too close to the TV, or if the
TV’s volume is too high, whistling or howling may
occur.
For Insert Editing/Audio Dubbing
• Insert Editing and Audio Dubbing may not work
correctly if the tape contains blank segments, or if
the recording speed was changed during the
original recording.
• To edit/dub onto a tape, make sure the erase
protection tab is in the position that allows
recording.
• Do not press STOP
U
during Insert Editing or
Audio Dubbing, or the edit points will not be
accurate.
