JUNO JKI 4053 Скачать руководство пользователя страница 6

14

INSTALLATION

Location

The appliance should be installed well away from
sources of heat such as radiators, boilers, direct
sunlight etc.

Electrical connection

Before plugging in, ensure that the voltage and
frequency shown on the serial number plate
correspond to your domestic power supply. Voltage
can vary by ±6% of the rated voltage.

For operation with different voltages, a suitably sized
auto-transformer must be used.

The appliance must be earthed.

The power supply cable plug is provided with a
contact for this purpose.

If the domestic power supply socket is not earthed,
connect the appliance to a separate earth in
compliance with current regulations, consulting a
specialist technician.

The Manufacturer declines all responsibility if

Instructions for totally built-in appliances

the above safety precautions are not observed.

This appliance complies with the following

E.E.C. Directives:

- 87/308 EEC

of 2/6/87 relative to radio interference

suppression.

- 73/23 EEC

of 19.2.73 (Low Voltage Directive) and

subsequent modifications;

- 89/336 EEC

of 3.5.89 (Electromagnetic

Compatibility Directive) and subsequent
modifications.

Door reversibility

The applianceÕs door have been locked in position
for transport by means of pins on both sides.
According to the door opening direction, remove
relevant pins at the top and at the bottom.

50 mm

min.

cm

2

 

 200

200 cm

2

min.

D567

Building-in instructions

Dimensions of housing

Model

JKI 4433

JKI 4453 JKI 4463

Hšhe

880 mm

1030 mm

1225 mm

Tiefe

550 mm

550 mm

550 mm

Breite

560 mm

560 mm

560 mm

For safety reasons, minimum ventilation must be as
shown in Fig.

Attention: keep ventilation openings clear of
obstruction.

CUSTOMER SERVICE AND SPARE PARTS

If the appliance is not functioning properly, check
that:

¥

the plug is firmly in the wall socket and the mains
power switch is on;

¥

there is an electricity supply (find out by plugging
in another appliance);

¥

the thermostat knob is in the correct position.

¥

If there are water drops on the bottom of the
cabinet, check that the defrost water drain

opening is not obstructed (see ÒDefrostingÓ
section).

¥

If your appliance is still not working properly after
making the above checks, contact the nearest
service centre.

To obtain fast service, it is essential that when you
apply for it you specify the model and serial number
of your appliance which can be found on the
guarantee certificate or on the rating plate located
inside the appliance, on the bottom left-hand side.

ATTENTION!

It must be possible to disconnect the appliance from
the mains power supply; the plug must therefore be
easily accessible after installation.

Содержание JKI 4053









Отзывы: