JUNO JDK5535-EF, Руководство по эксплуатации

Страница: 3 / 11

7
4.3 - Connect the hood to the mains supply and ensure that it works properly
4.4 - Set the hood for recirculation or extraction
4.5 - Fix the telescopic metal frame
4.1 - Fixing the wall brackets (Optional)
Ref. to Fig. 2 a-b
1 - Draw a vertical line on the wall from the centre of the cooking appliance up to the ceiling, using
a marking pen. This is to ensure the correct vertical alignment of many components.
2 - Fixing the wall bracket No. 1:
a - put the bracket l to the wall, aligning its marked centre across the vertical line, ensuring that the
distance between the centres of the holes and the cooking area is as follows:
1 - when the splashback is to be installed: d=197mm+H mm, where H is the height of the visible
part of the splashback. As the splashback can be of different heights, the correct H figure can only
be obtained by measuring the actual height of the splashback to be fitted.
2 - without splashback: d=847 mm minimum.
Note: ensure that the wall bracket (l) is levelled. The hood can be aligned or adjusted in height
by rotating the adjustment screws (see below).
b - mark on the wall the centres of the two keyholes of the bracket.
3 - Fixing the wall brackets item 2
a - Place one of the two brackets (item 2 Fig. 1) 15 mm from the ceiling or from a horizontal line
drawn between the top of the adjoining wall cabinets, ensuring that the bracket is level and mark
the centres for the keyhole bracket fixing screws.
b - Place the other wall bracket (item 2 Fig. 1) on the wall at “X” distance. This measurement
should be determined by the height of the upper chimney stack and mark the centres for the keyhole
bracket fixing screws.
4 - Pilot drill all the hole positions as marked on the wall using an 8 mm drill and fix the wall brackets
1-2 using the rawl plugs and screws supplied.
5 - Splashback (optional)
When a splashback is to be fitted, the distance between the cooker hood and the cooking appliances
will be determined by the height of the splashback, item F. The splashback is to be installed before
installing the canopy. If the splashback is to be fixed to the wall using both the top and bottom
fixing holes care must be taken to ensure that the splashback is fitted at the correct height before
fixing it into position.
The fitting should be undertaken by a competent person with experience in this type of installation.
If the splashback is to be fixed through only the top fixing holes proceeds as follows:
a - Put the splashback on the worktop as illustrated in Fig. 2a; then holding it against the wall to
ensure that it is correctly positioned mark the holes for the top fixing screws on the wall.
b - Pilot drill the wall using an 8 mm drill and fix the splashback using the 8 mm rawl plugs and
screws supplied.
c - If the fixing holes in the bottom of the splashback are not to be used to secure the splashback
to the wall the installer should ensure that the bottom edge is tucked down behind the rear of the
worktop.
4.2 - Fixing the canopy hood (Fig. 3)
1 - Adjust the two screws V (on the canopy connection points) to approximately half way.
2 - Hook the rear of the canopy to the wall bracket 1, after anchoring the latter to the wall.
3 - Turn the screws V to adjust the canopy vertically and level it horizontally.
4 - Fit and lock the central fixing screw V1 (provided) to lock the canopy in place.
4.3 - Electrical connection and working test
1 - The safety measures 3.2, 3.3 and 3.4 of paragrapf 3 are to be strictly observed.
2 - Once the electrical connection has been completed, check that worktop illumination, motor and
speed work properly.