Juniper SSG 20-WLA Скачать руководство пользователя страница 70

Страница: 70 / 82

SSG 20 Hardware Installation and Configuration Guide

7. E1 Interface Windows

If you have the E1 mini PIM installed on your device and select the Frame Relay
option, the following windows are displayed:

“E1 Physical Layer Tab Window” on page X

“E1 Frame Relay Tab Window” on page XI

Figure 10: E1 Physical Layer Tab Window

Table 8: Field Description for E1 Physical Layer Tab

NOTE:

If you have two E1 mini PIMs installed on your device and you select the

Multi-link

option, you will see two Physical Layer tabs.

Field

Description

Clocking

Sets the transmit clock on the interface

Frame Checksum

Sets the size of checksum. Default is 16

Framing Mode

Sets the framing format. Default is without CRC4

Idle Cycles Flag

Sets the value that the interface transmits during idle cycles. Default
setting is 0x7E

0x7E (flags)

0xFF (ones)

Start/End Flags

Sets the transmission of start and end flags to either filler or shared.
The default is filler

Invert data checkbox

Enables inverted transmission of unused data bits

Time slots

Sets the use of time slots on a T1 interface. Default is

, all 32 time

slots used

Содержание SSG 20-WLA



















































































Результаты поиска

Содержание SSG 20-WLA

Отзывы:

Бренды по названию

Популярные бренды

Juniper SSG 20-WLA, Руководство по установке и настройке оборудования

Результаты поиска

Содержание SSG 20-WLA

Отзывы:

Бренды по названию

Популярные бренды