Juniper SRX240 Series Скачать руководство пользователя

Страница: 125 / 198

CHAPTER 17

Troubleshooting Components

•

Monitoring the SRX240 Services Gateway Components Using LEDs on page 107

•

Monitoring the SRX240 Services Gateway Chassis Using the CLI on page 111

•

Monitoring the SRX240 Services Gateway Using Chassis Alarm Conditions on page 113

•

Monitoring the SRX240 Services Gateway Power System on page 115

•

Loading the Rescue Configuration on the SRX240 Services Gateway on page 117

•

Changing the Reset Config Button Behavior on the SRX240 Services
Gateway on page 118

•

Juniper Networks Technical Assistance Center on page 118

Monitoring the SRX240 Services Gateway Components Using LEDs

The LEDs on the services gateway display the status of various components.

Table 41 on page 107

describes the LEDs.

Table 41: Component LEDs on the SRX240 Services Gateway

Possible Causes and
Corrective Actions

Meaning

State

LED

Normal condition. No action
is required.

The services gateway is
functioning normally.

Green

Status LED

Normal condition. No action
is required.

•

The services gateway is
starting up.

•

The RESET CONFIG
button is pressed.

Yellow

Contact the Juniper
Networks Technical
Assistance Center (JTAC).
See

“Juniper Networks

Technical Assistance
Center” on page 118

An error is detected in the
services gateway.

Red

107

Содержание SRX240 Series










































































































































































Результаты поиска

Содержание SRX240 Series

Отзывы:

Похожие инструкции для SRX240 Series

Бренды по названию

Популярные бренды

Juniper SRX240 Series, Руководство по оборудованию

Результаты поиска

Содержание SRX240 Series

Отзывы:

Похожие инструкции для SRX240 Series

Бренды по названию

Популярные бренды