Juniper QFX5120 Series Скачать руководство пользователя страница 79

Страница: 79 / 207

13 dBm – 0.5 dBm – 2.5 dBm – 1 dBm – 2 dBm – 1 dBm = P

= 6 dBm

The calculated power margin is greater than zero, indicating that the link has sufficient power for

transmission. Also, the power margin value does not exceed the maximum receiver input power.

Refer to the specifications for your receiver to find the maximum receiver input power.

QFX5120 Management Cable Specifications and
Pinouts

IN THIS SECTION

Console Port Connector Pinout Information | 81

RJ-45 Management Port Connector Pinout Information | 82

RJ-45 to DB-9 Serial Port Adapter Pinout Information | 83

QSFP+,QSFP28, SFP, SFP+, and SFP28 Port Connector Pinout Information | 83

Console Port Connector Pinout Information

The console port on a Juniper Networks device is an RS-232 serial interface that uses an RJ-45 connector

to connect to a console management device. The default baud rate for the console port is 9600 baud.

Table 32 on page 82

provides the pinout information for the RJ-45 console connector.

NOTE:

If your laptop or PC does not have a DB-9 male connector pin and you want to connect

your laptop or PC directly to a device, use a combination of the RJ-45 to DB-9 female adapter and

a USB to DB-9 male adapter. You must provide the USB to DB-9 male adapter.

Содержание QFX5120 Series
















































































































































































































Результаты поиска

Содержание QFX5120 Series

Отзывы:

Бренды по названию

Популярные бренды

Juniper QFX5120 Series, Руководство по оборудованию

Результаты поиска

Содержание QFX5120 Series

Отзывы:

Бренды по названию

Популярные бренды