Juniper QFX5120 Series Скачать руководство пользователя

Страница: 136 / 207

Before you begin to disconnect a fiber-optic cable from an optical transceiver, ensure that you have taken

the necessary precautions for safe handling of lasers. See

“Laser and LED Safety Guidelines and Warnings”

on page 178

Ensure that you have the following parts and tools available:

•

A rubber safety cap to cover the transceiver

•

A rubber safety cap to cover the fiber-optic cable connector

To disconnect a fiber-optic cable from an optical transceiver installed in the device:

1. Disable the port in which the transceiver is installed by issuing the following command:

[edit interfaces]

user@device#

set

interface-name

disable

WARNING:

Do not look directly into a fiber-optic transceiver or into the ends of

fiber-optic cables. Fiber-optic transceivers and fiber-optic cables connected to

transceivers emit laser light that can damage your eyes.

2. Carefully unplug the fiber-optic cable connector from the transceiver.

3. Cover the transceiver with a rubber safety cap.

WARNING:

Do not leave a fiber-optic transceiver uncovered except when inserting

or removing a cable. The rubber safety cap keeps the port clean and prevents accidental

exposure to laser light.

4. Cover the fiber-optic cable connector with the rubber safety cap.

Maintaining Fiber-Optic Cables

Fiber-optic cables connect to optical transceivers that are installed in Juniper Networks devices.

To maintain fiber-optic cables:

140

Содержание QFX5120 Series
















































































































































































































Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды

Juniper QFX5120 Series, Руководство по оборудованию

Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды