Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are
trademarks of Juniper Networks, Inc. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies
in this document. Juniper Networks reserves the right to change, modify, transfer, or otherwise revise this publication without notice. Products made or sold by Juniper Networks or components thereof might be covered by one or more
of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899,
6,552,918, 6,567,902, 6,578,186, and 6,590,785. Copyright © 2015 Juniper Networks, Inc. All rights reserved. Printed in China. Part Number: 530-064558 Revision 01, 1 May 2015.
z
Flow Control—None
z
Data—8
z
Parity—None
z
Stop Bits—1
z
DCD State—Disregard
To connect and configure the switch from the console:
1. Connect the console port to a laptop or PC using the provided RJ-45 cable and RJ-45
to DB-9 serial port adapter. The console (
CON
) port is located on the management
panel of the switch.
2. Log in as
root
. There is no password. If the software booted before you connected
to the console port, you might need to press the Enter key for the prompt to appear.
login:
root
3. Start the command-line interface (CLI).
root@%
cli
4. Enter configuration mode.
root>
configure
5. Add a password to the root administration user account.
[edit]
root@#
set system root-authentication plain-text-password
New password:
password
Retype new password:
password
6. (Optional) Configure the name of the switch. If the name includes spaces, enclose
the name in quotation marks (“ ”).
[edit]
root@#
set system host-name
host-name
7. Configure the default gateway.
[edit]
root@#
set routing-options static route default next-hop
address
8. Configure the IP address and prefix length for the switch management interface.
[edit]
root@#
set interfaces em0 unit 0 family inet address
address/prefix-length
NOTE:
The RJ-45 management port,
em0
and the SFP management port,
em1
,
are
found on the port end of the QFX10002. They are both labeled
MGMT
.
9. (Optional) Configure the static routes to remote prefixes with access to the
management port.
[edit]
root@#
set routing-options static route
remote-prefix
next-hop
destination-ip
retain no-readvertise
10. Enable telnet service.
[edit]
root@#
set system services telnet
11. Commit the configuration to activate it on the switch.
[edit]
root@#
commit
Safety Warnings Summary
This is a summary of safety warnings. For a complete list of warnings, including
translations, see the QFX10002 switch documentation at
http://www.juniper.net/techpubs/.
WARNING:
Failure to observe these safety warnings can result in personal injury
or death.
z
Permit only trained and qualified personnel to install or replace switch components.
z
Perform only the procedures described in this quick start and the QFX10002 switch
documentation. Other services must be performed only by authorized service
personnel.
z
Before installing the switch, read the planning instructions in the QFX10002 switch
documentation to make sure that the site meets power, environmental, and clearance
requirements for the switch.
z
Before connecting the switch to a power source, read the installation instructions in the
10002 switch documentation.
z
The QFX10002-72Q weighs 68.6 lbs (31.1 kg) and the QFX10002-36Q weighs 54 lbs
(24.5 kg). Installing the QFX10002 switch in a rack or cabinet requires either a
mechanical lift or two people to lift the switch and another person to secure it to the
rack. To prevent injury, keep your back straight and lift with your legs, not your back.
z
If the rack or cabinet has stabilizing devices, install them in the rack before mounting or
servicing the switch in the rack or cabinet.
z
Before installing or after removing an electrical component, always place it
component-side up on a flat antistatic mat or in an antistatic bag.
z
Do not work on the switch or connect or disconnect cables during electrical storms.
z
Before working on equipment that is connected to power lines, remove jewelry,
including rings, necklaces, and watches. Metal objects heat up when connected to
power and ground and can cause serious burns or become welded to the terminals.
CAUTION:
Do not place a copper transceiver in an access port directly above or
below another copper transceiver. Damage to the access ports will occur.
Power Cable Warning (Japanese)
The attached power cable is only for
this product. Do not use this cable for
another product.
Contacting Juniper Networks
For technical support, see
http://www.juniper.net/support/requesting-support.html .
G
