manualshive.com logo in svg

Juniper PTX3000, Быстрый старт, Страница: 7 / 37

Поделиться
Скачать
Juniper PTX3000 Скачать руководство пользователя страница 7

Step 4: Install the PTX3000 Packet Transport Router

Because of the size and weight of the device, we recommend that you install the packet
transport router by using a mechanical lift.

•

Install the Packet Transport Router By Using a Lift on page 7

Install the Packet Transport Router By Using a Lift

CAUTION:

Before installing the PTX3000 Packet Transport Router:

•

Verify that a mechanical lift is available for the installation.

•

Have a qualified technician verify that the rack is strong enough to support
the chassis weight and is adequately supported at the installation site.

•

Ensure that the rack is in its permanent location and is secured to the
building.

•

Ensure that the installation site allows adequate clearance for both airflow
and maintenance.

NOTE:

A mounting shelf is not required to install the packet transport router.

To install the packet transport router using a lift (see

Figure 3 on page 9

and

Figure 4 on page 10

):

1.

Load the packet transport router onto the lift, making sure the packet transport router
rests securely on the mechanical lift.

CAUTION:

Do not lift the packet transport router by using the handles on

the front-mounting flanges. Use these handles only to help position the
packet transport router.

2.

Using the lift, position the packet transport router in front of the rack. Lift the chassis
slightly above the position you plan to install it, and position it as close as possible to
the rack.

3.

With two people in front, push the front-mounting flanges to slide the packet transport
router into the rack until the front-mounting flanges contact the rack rails. The
front-mounting flanges of the chassis align with the holes in the rack rails.

4.

Install a mounting screw into each of the mounting holes aligned with the rack, starting
from the bottom (

Table 3 on page 8

). Use an appropriate screwdriver to tighten all

the screws completely.

Visually inspect the alignment of the packet transport router. If the packet transport
router is installed properly in the rack, all the mounting screws on one side of the rack

7

Copyright © 2014, Juniper Networks, Inc.

Step 4: Install the PTX3000 Packet Transport Router

Содержание PTX3000






































Отзывы:

Нет отзывов