manualshive.com logo in svg

Juniper PTX3000, Быстрый старт, Страница: 26 / 37

Поделиться
Скачать
Juniper PTX3000 Скачать руководство пользователя страница 26

Figure 24: Installing an AC PSM

g0

0

7

5

4

2

10.

Repeat the procedure for the remaining PSMs.

11.

Verify that the AC power cords do not drape where people could trip on them.

Step 8: Power On the PTX3000 Packet Transport Router

To power on the packet transport router, perform one of the following procedures:

•

Power On the DC-Powered PTX3000 Packet Transport Router on page 26

•

Power On the AC-Powered PTX3000 Packet Transport Router on page 27

Power On the DC-Powered PTX3000 Packet Transport Router

To power on the DC-powered packet transport router:

NOTE:

After powering off a power supply, you must wait at least 60 seconds

before powering it on again.

1.

Verify that the power supply modules (PSMs) are fully inserted in the chassis and
that the captive screw on the faceplate of each PSM is tightened.

2.

Verify that an external management device is connected to one of the Routing Engine
ports on the Control Board (

AUX

or

CON

).

NOTE:

The management Ethernet port labeled

HOST/ETHERNET

on the

Control Board is not available until after the initial software configuration.
You can monitor the startup process during the initial installation by using
devices connected to the

AUX

or

CON

ports.

3.

Turn on the power to the external management device.

Copyright © 2014, Juniper Networks, Inc.

26

PTX3000 Packet Transport Router Quick Start

Содержание PTX3000






































Отзывы:

Нет отзывов