Juniper MX2010 Скачать руководство пользователя страница 587

Страница: 587 / 825

MX2000 Three-Phase Delta and Wye AC Power Distribution Module LEDs | 107

Connecting AC Power to an MX2000 Router with Three-Phase Delta AC Power Distribution

Modules | 291

Troubleshooting the MX2000 Router Power System | 320

MX2000 AC Power Cord Specifications | 170

MX2000 Three-Phase Delta AC Power Distribution Module Electrical Specifications | 178

Replacing an MX2000 Three-Phase Delta AC Power Distribution Module

Removing an MX2000 Three-Phase Delta AC Power Distribution Module | 571

Installing an MX2000 Router Three-Phase Delta AC Power Distribution Module | 576

Removing an MX2000 Three-Phase Delta AC Power Distribution Module

NOTE:

The MX2008, MX2010, and MX2020 routers support the same power modules (AC/DC

PSMs and AC/DC PDMs).

Before you remove a three-phase delta AC PDM, be aware of the following:

WARNING:

Before performing AC power procedures, disconnect all power sources.

To ensure that all power is OFF, locate the circuit breaker on the panel board that

services the AC circuit, switch the circuit breaker to the OFF position, and tape the

switch handle of the circuit breaker in the OFF position.

WARNING:

Do not touch the power connectors on the PDM. They can contain

dangerous voltages.

CAUTION:

To maintain proper cooling and prevent thermal shutdown of the operating

power supply unit, each PDM slot must contain either a PDM or a blank panel. If you

remove a PDM, you must install a replacement PDM or a blank panel shortly after the

removal.

571

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Juniper MX2010, Руководство по оборудованию, Страница: 587 / 825

Результаты поиска

Содержание MX2010

Отзывы: