Juniper MX2010 Скачать руководство пользователя страница 521

Страница: 521 / 825

Replacing the MX2010 Extended EMI Cover

IN THIS SECTION

Removing the MX2010 Extended EMI Cover | 505

Installing the MX2010 Extended EMI Cover | 506

Removing the MX2010 Extended EMI Cover

The extended electromagnetic interference (EMI) cover attaches to the router over the card cage and tilts

out from the top.

To remove the extended electromagnetic interference (EMI) card-cage cover (see

Figure 263 on page 506

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to

one of the ESD points on the chassis.

2. Gripping the flap on the extended EMI cover, tilt it away from the router toward you.

3. Holding the cover on both sides, lift so that the points on the cover lift out of the grooves on the EMI

cover brackets.

4. Pull the cover away from the router toward you to remove it.

5. Using a number 2 Phillips (+) screwdriver, remove the two mounting screws from the mounting brackets

on either side of the card cage. Then remove the mounting brackets (see

Figure 262 on page 506

505

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды