manualshive.com logo in svg

Juniper MX2010, Руководство по оборудованию

Juniper MX2010 - мощный маршрутизатор для крупных сетей. Желающие могут бесплатно скачать его аппаратное руководство с {веб-сайта}. Этот manual поможет вам узнать о всех возможностях и функциях устройства для оптимальной работы с сетями любого масштаба.

Поделиться
Скачать
background image

Figure 210: Removing a CB-RE

g007029

19

0

OK/FAIL

OK/FAIL

OK/FAIL

OK/FAIL

OK/FAIL

OK/FAIL

OK/FAIL

OK/FAIL

Installing the REMX2K-X8-64G CB-RE

To install the new REMX2K-X8-64G CB-RE (see

Figure 211 on page 443

):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to

one of the ESD points on the chassis.

2. Remove the CB-RE from the electrostatic bag.

3. Carefully align the sides of the CB-RE with the guides inside the chassis.

4. Slide the CB-RE into the chassis until you feel resistance, carefully ensuring that it is correctly aligned.

5. Grasp both ejector handles, and gently close them inward simultaneously until the CB-RE is fully seated.

6. Check the LEDs on the CB-RE faceplate to verify that it is functioning normally.

•

The green ONLINE LED should blink green initially and light steadily a few minutes after the CB-RE
is installed.

442

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX2010

ICP DAS USA ET-7000 series Quick Start Manual preview
ET-7000 series
Бренд: ICP DAS USA Страницы: 14
ICP DAS USA I-2533 User Manual preview
I-2533
Бренд: ICP DAS USA Страницы: 25
ICP DAS USA ET-2200 Series Manual preview
ET-2200 Series
Бренд: ICP DAS USA Страницы: 15
ICP ZT-2550 Quick Start Manual preview
ZT-2550
Бренд: ICP Страницы: 14
Radwin Transportation FiberinMotion Deployment Manual preview
Transportation FiberinMotion
Бренд: Radwin Страницы: 122
TP-Link VIGI NVR1008 Quick Installation Manual preview
VIGI NVR1008
Бренд: TP-Link Страницы: 2
B&B Electronics Parallel & Serial Port Checker PPC User Manual preview
Parallel & Serial Port Checker PPC
Бренд: B&B Electronics Страницы: 4
Garderos R-7700 Series Operating Manual preview
R-7700 Series
Бренд: Garderos Страницы: 23
EMCIS LISN User'S Operating Manual preview
LISN
Бренд: EMCIS Страницы: 14
Ubiquiti UniFi Cloud Key Quick Start Manual preview
UniFi Cloud Key
Бренд: Ubiquiti Страницы: 13
Xantech IR-X10 Installation Instructions Manual preview
IR-X10
Бренд: Xantech Страницы: 16
Dynamix UM-S User Manual preview
UM-S
Бренд: Dynamix Страницы: 102
Intellinet 720564 Instructions preview
720564
Бренд: Intellinet Страницы: 2
TRENDnet TEW-823DRU Quick Installation Manual preview
TEW-823DRU
Бренд: TRENDnet Страницы: 10
EMC VNX5300 Block Hardware Information Manual preview
VNX5300 Block
Бренд: EMC Страницы: 88
ZyXEL Communications Prestige 643 User Manual preview
Prestige 643
Бренд: ZyXEL Communications Страницы: 191
DayTronic PC-HSICA Instruction Manual preview
PC-HSICA
Бренд: DayTronic Страницы: 13
Idis DR-8516 Installation Manual preview
DR-8516
Бренд: Idis Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды