Juniper MX2010 Скачать руководство пользователя страница 301

Страница: 301 / 825

Figure 121: Reinstalling an SFB

OK/FAIL

g007418

OK/FAIL

Reinstalling the Adapter Card

To reinstall an adapter card (see

Figure 122 on page 285

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to

one of the ESD points on the chassis.

2. Take each adapter card to be installed out of its electrostatic bag, and identify the slot where it will be

installed.

3. Locate the slot in the card cage in which you plan to install the adapter card.

4. Ensure that the adapter card is right-side up, with the text on the faceplate facing upward.

5. Lift the adapter card into place, and carefully align first the bottom, and then the top of the adapter

card with the guides inside the card cage.

6. Slide the adapter card all the way into the card cage until you feel resistance.

7. Grasp both ejector handles, and gently close them inward simultaneously until the adapter card is fully

seated.

284

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды