Juniper MX2010 Скачать руководство пользователя страница 195

Страница: 195 / 825

Table 56: MX2000 AC Power System Electrical Specifications

Specification

Item

Delta operating range: 200–240 VAC (line-to-line) (nominal)

Wye operating range: 200–240 VAC (line-to-neutral) (nominal)

Single-phase operating range: 200-240 VAC (nominal)

AC input voltage

Delta: 50/60 Hz (+/-3Hz)

Wye: 50/60 Hz (+/-3Hz)

Single-phase: 50/60 Hz (+/-3Hz)

AC input line frequency

Delta: 50 A @ 200 VAC–(input #1 for each PDM) and 25 A @

200 VAC–(input #2 for each PDM)

Wye: 30 A @ 200 VAC–(input #1 for each PDM) and 15 A @

200 VAC–(input #2 for each PDM)

Single-phase: 30 A @ 200 VAC

AC system current rating

Delta: 16800 W (input #1), 8400 W (input #2)

Wye: 16800 W (input #1), 8400 W (input #2)

AC system input power

90.5% at 50% load and 220 VAC IN

Efficiency

AC Power Supply Input Fuses

The AC PSM has line and neutral power supply input fuses in both INP0 and INP1.

Table 57 on page 174

lists the electrical specifications for each fuse.

Table 57: Electrical Specifications for AC Power Supply Input Fuses

Value

Electrical Characteristic

Littelfuse 0324020.MX65LP

INP0/INP1 Line Fuse

20A

•

Ampere Rating

250V

•

Voltage Rating

1000A @ 250V

•

Interrupting Rating

3.55 mOhm

•

Nominal Cold Resistance

174

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Бренды по названию

Популярные бренды