manualshive.com logo in svg

Juniper MX2010, Руководство по оборудованию

Juniper MX2010 - мощный маршрутизатор для крупных сетей. Желающие могут бесплатно скачать его аппаратное руководство с {веб-сайта}. Этот manual поможет вам узнать о всех возможностях и функциях устройства для оптимальной работы с сетями любого масштаба.

Поделиться
Скачать
background image

RELATED DOCUMENTATION

MX2010 Chassis Moving Guidelines | 129

MX2010 Router Overview | 3

MX2010 Chassis Description | 7

MX2010 Rack Requirements

IN THIS SECTION

Rack Size and Strength | 135

Spacing of Mounting Bracket and Flange Holes | 137

Connection to the Building Structure | 138

Rack Size and Strength

The MX2010 router is designed for installation in a rack that complies with either of the following standards:

•

A 19-in. rack as defined in Cabinets, Racks, Panels, and Associated Equipment (document number EIA-310-D)

published by the Electronics Components Industry Association (

http://www.ecianow.org/

).

•

A 600-mm rack as defined in the four-part Equipment Engineering (EE); European telecommunications

standard for equipment practice (document numbers ETS 300 119-1 through 119-4) published by the

European Telecommunications Standards Institute (ETSI). The horizontal spacing between the rails in a

rack that complies with this standard is usually wider than the mounting brackets, which measure

19.2 in. (48.8 cm) from the outer edge to outer edge. Use approved wing devices to narrow the opening

between the rails as required.

•

A 23-in. rack using appropriate 23-in. to 19-in. rack adapters and an appropriate installation shelf that

supports the chassis at the correct vertical position to properly line up the rack mount holes. Juniper

Networks does not supply this hardware, but consideration for the size and weight of the chassis is

important for a safe installation.

The rack rails must be spaced widely enough to accommodate the chassis’s external dimensions:

59.50 in. (151.1 cm) high, 36.20 in. (91.95 cm) deep, and 19 in. (48.3 cm) wide. The outer edges of the

front-mounting flanges extend the width to 19.2 in. (48.8 cm), The spacing of rails and adjacent racks must

also allow for the clearances around the chassis and rack that are specified in

“Clearance Requirements

for Airflow and Hardware Maintenance for the MX2010 Router” on page 147

. The cable manager and EMI

135

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX2010

Habitat M10 Installation Manual preview
M10
Бренд: Habitat Страницы: 48
ZyXEL Communications ZyAIR G-3000H User Manual preview
ZyAIR G-3000H
Бренд: ZyXEL Communications Страницы: 299
Xircom RealPort Ethernet 10/100 User Manual preview
RealPort Ethernet 10/100
Бренд: Xircom Страницы: 30
Tektronix CTS 850 User Manual preview
CTS 850
Бренд: Tektronix Страницы: 178
AYRSTONE AyrMesh IndoorAP Instructions preview
AyrMesh IndoorAP
Бренд: AYRSTONE Страницы: 2
Paradyne Hotwire 8775 MSDSL Installation Instructions Manual preview
Hotwire 8775 MSDSL
Бренд: Paradyne Страницы: 10
Divio SRA311-008P8 Series Installation Manual preview
SRA311-008P8 Series
Бренд: Divio Страницы: 4
Network Critical SmartNA-X User Manual preview
SmartNA-X
Бренд: Network Critical Страницы: 200
Vacron VDH-NK300 Hardware Manual preview
VDH-NK300
Бренд: Vacron Страницы: 16
Broadband Products D-Link DSL-2640U Quick Installation Manual preview
D-Link DSL-2640U
Бренд: Broadband Products Страницы: 12
Teldat G1N Installation Manual preview
G1N
Бренд: Teldat Страницы: 23
Ubiquiti EdgeRouter X Quick Start Manual preview
EdgeRouter X
Бренд: Ubiquiti Страницы: 20
Draytek Vigor1000B Quick Start Manual preview
Vigor1000B
Бренд: Draytek Страницы: 17
Omron JUNMA PULSE Datasheet preview
JUNMA PULSE
Бренд: Omron Страницы: 4
Delta Electronics CANopen Communication Module DVPCP02-H2 Instruction Manual preview
CANopen Communication Module DVPCP02-H2
Бренд: Delta Electronics Страницы: 2
G&D ControlCenter-IP 2.0 Installation Manual preview
ControlCenter-IP 2.0
Бренд: G&D Страницы: 60
ZyXEL Communications WAP6804 User Manual preview
WAP6804
Бренд: ZyXEL Communications Страницы: 114
IBM TS4300 Manual preview
TS4300
Бренд: IBM Страницы: 288

Бренды по названию

Популярные бренды

Загрузить еще бренды