Juniper MX2008 Скачать руководство пользователя страница 48

Страница: 48 / 69

WARNING:

Power connections must be performed by a licensed electrician

only.

12.

Verify that the power cable connections are correct.

13.

Screw the retaining nut onto the AC power cord to secure it to the metal wiring
compartment.

14.

Using a number 2 Phillips (+) screwdriver, tighten the two captive screws on the metal
AC wiring compartment.

15.

Use the provided plastic cable tie to fasten the AC power cord to the PDM.

16.

Verify that the AC power cord does not touch or block access to router components,
and that it does not drape where people could trip on it.

17.

Repeat the procedure for the other three-phase delta AC PDMs.

18.

Connect the three-phase delta AC power cord mating connector to the AC power
cord connector (see

Figure 35 on page 48

Table 5 on page 48

shows the approved

three-phase delta AC power cord mating connector specifications.

Figure 35: Three-Phase Delta AC Power Cord Mating Connector

g000037

NOTE:

The three-phase delta AC power cord mating connector is not

supplied by Juniper Networks.

Table 5: Three-Phase Delta AC Power Cord Mating Cable Connector
Specifications

Description

Manufacturer Part Number

Cable

60-amp, 250 volt 3-phase,
3-pole, 4-wire, North
American pin and sleeve
connector, industrial grade,
IP67, watertight (blue)

460C9W

Three-phase delta

MX2008 3D Universal Edge Router Quick Start

Содержание MX2008



































































Результаты поиска

Содержание MX2008

Отзывы:

Похожие инструкции для MX2008

Бренды по названию

Популярные бренды

Juniper MX2008, Быстрый старт

Результаты поиска

Содержание MX2008

Отзывы:

Похожие инструкции для MX2008

Бренды по названию

Популярные бренды