manualshive.com logo in svg

Juniper ACX2200, Быстрый старт

Поделиться
Скачать
Juniper ACX2200 Скачать руководство пользователя страница 7

Step 2: Install the Router

•

Tools Required to Install the Router in a Rack on page 7

•

Install the Mounting Brackets on page 7

•

Install the ACX2200 Router in the Rack on page 8

Tools Required to Install the Router in a Rack

To install the router in a rack, you need the following tools:

•

Phillips (+) screwdriver, number 2

•

ESD grounding wrist strap

Install the Mounting Brackets

Two mounting brackets for front or rear mounting ship with the router (see

Figure 4 on page 7

and

Figure 5 on page 7

).

Attach both mounting brackets to either the front or rear of the chassis:

1.

Align the bracket with the two sets of mounting holes.

2.

Insert the four screws at the top and bottom of the bracket and tighten each partially.

3.

Tighten the four screws completely.

4.

Repeat the procedure for the other bracket.

Figure 4: Installing the Mounting Brackets to the Front of the ACX2200
Router

g006405

Figure 5: Installing the Mounting Brackets to the Rear of the ACX2200
Router

g006406

7

Copyright © 2016, Juniper Networks, Inc.

Step 2: Install the Router

Содержание ACX2200

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды