Jungheinrich ETX 513 Скачать руководство пользователя | Manualshive

Страница: 72 / 408

background image

4.3

Commissioning

91

92

93

94

95

Preparing the truck for operation after delivery or transport

Requirements

– Unload the truck from the van, lorry or trailer.
– Assemble the mast. The mast can only be assembled by the manufacturer's

specialist customer service personnel who have been trained to do this.
Exceptionally, this task may be performed by a customer service organisation
authorised by the manufacturer.

Tools and Material Required

– Cable ties.
– Adhesive tape.
– Allen key (key width 4) to undo the load wheel panels.
– Allen key (key width 5) to undo the screws (94).
– For ETX 515 only:

Allen key (key width 6) to undo the setscrews (93).

Procedure

• Check the equipment is complete.
• Loosen the transport chains (91).
• Remove the load wheel brake transport retainers (ETX 515 only).

Z

The transport retainers release the load wheel brakes when they are de-
energised.
• Disassemble the load wheel guards by removing the three Allen screws from

the load wheels.

• Remove the transport retainers from the load wheel brakes (92) by removing

three setscrews (93) from the load wheel brakes (92).

The load wheel brakes (92) are now applied without power.

• Store the setscrews (93) in the plastic bag supplied.
• Seal the plastic bag with adhesive tape.

• Store the plastic bag and setscrews (93) in the drive compartment.

• Open the drive compartment cover (95), see page 330.
• Fix the plastic bag in the drive compartment with cable ties so that it does not

come into contact with moving parts while the truck is moving.

• Close the drive compartment cover (95), see page 330.

• Fit the panels of the load wheels (24) on both sides:

• Place the panels onto the load wheels.
• Attach the panels to the load wheel with three Allen screws.

70

04.19 en-GB

«
...
70
71
72
73
74
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ETX 513

Бренд: BOSCARO Страницы: 12

Бренд: Jungheinrich Страницы: 157

Бренд: Dini Argeo Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды