Jungheinrich ETX 513 страница 300 Скачать руководство пользователя | Manualshive

Страница: 300 / 408

background image

8.12.2

Lifting the work platform with the standard attachment

If, in an exceptional circumstance
approved by the owner, the work
platform is to be raised and an operator
carried in the work platform, proceed as
follows:

Requirements

– Prepare the truck for operation, see

page 139 or see page 140.

Tools and Material Required

– Use only work platforms that have been

approved for this truck by the owner.

Procedure

• Check the work platform for damage

before using it.

• Check the lock (243) on the work

platform is present and check for damage.

• Close the gate (239).

Z

The work platform must be lifted in such a way that at all times during travel, lifting
or lowering, eye contact is maintained between the driver and the operator of the
work platform.

• Before raising the work platform make sure there is no one inside it.
• Position the truck in front of the work platform so that the forks can be inserted

into the fork shoes (241).

240

241

239

242

243

244

236

237

238

298

04.19 en-GB

«
...
298
299
300
301
302
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ETX 513

Бренд: Still Страницы: 130

Бренд: HANGCHA Страницы: 108

Бренд: Presto Lifts Страницы: 29

PPS2200-62NFO-21

Бренд: Presto Lifts Страницы: 31

Бренд: Clark Страницы: 78

Бренд: Clark Страницы: 88

Бренд: Clark Страницы: 128

Бренд: Clark Страницы: 144

Бренд: Clark Страницы: 170

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды