Jungheinrich ETX 513 Скачать руководство пользователя страница 241 | Manualshive

Страница: 241 / 408

Jungheinrich ETX 513 Скачать руководство пользователя страница 241

7.6

Daily checks before starting the Personal Protection System

– Check the front screens of the Personal Protection System laser scanner for

contamination and clean as required (see page 236).

– Cycle test (see page 239)

7.6.1

Cycle test

NOTICE

To ensure the correct operation of the personal protection system a cycle test must
be carried out after a 24 hour timer has expired or each time the truck is switched off
and on again.

u

The information message "9901" and the "Perform cycle test" symbol (130)
prompt you to perform the cycle test. During this time the travel speed is restricted
to slow travel (2,5 km/h).

u

The speed restriction is only removed when the cycle test has been performed.

Cycle test

Procedure

• Switch off the truck.
• Switch on the truck.

Z

When the truck is switched on the
display unit shows the “Acknowledge
cycle test” symbols (130,189).

• Press (104) under the "Acknowledge

cycle test" symbol (189).

The truck automatically performs the
cycle test.

• When the cycle test has been successfully performed:

• The "Perform cycle test" symbol (130,189) fades out.
• The speed restriction is removed.
• The 2424 hour timer is reset and starts afresh.

The cycle test has been performed successfully.

130

189

104

239

04.19 en-GB

«
...
239
240
241
242
243
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды