manualshive.com logo in svg

Jungheinrich ETX 513, Руководство по эксплуатации

Поделиться
Скачать
Jungheinrich ETX 513 Скачать руководство пользователя страница 181

• Synchonised fork carriage 90° right rotation and load handler centre traverse:

• Press  and  hold  down  on  the    (104)  button  under  the  "Synchronised  rotation

until  forks  in  centre  position"  symbol  (169)  until  the  attachment  comes  to  rest
and rotary movement stops.

• Turn the "Hydraulic functions" control lever (113) anti-clockwise until you reach

the centre position.

• Synchonised fork carriage 90° left rotation and load handler centre traverse:

• Press  and  hold  down  on  the    (104)  button  under  the  "Synchronised  rotation

until  forks  in  centre  position"  symbol  (169)  until  the  attachment  comes  to  rest
and rotary movement stops.

• Turn the "Hydraulic functions" control lever (113) clockwise until you reach the

centre position.

The attachment is in the centre position and the forks are at right angles (90°) to the
truck. Loads can now be lifted from the front.

Z

If  the  attachment  is  not  in  the  centre  position,  you  can  only  travel,  lift  or  lower  at
reduced speed, see page 182.

4.14.6

Automatic synchronised rotation until forks are in centre position (

o

)

Z

With  "automatic  synchronised  rotation  until  forks  are  in  centre  position"  the  fork
carriage  is  rotated  90°  from  the  home  position  and  the  attachment  is  positioned  in
the centre of the traverse/pivot frame.

Requirements

– Prepare the truck for operation, see page 139 or see page 140.

Procedure

• Do not press the deadman button (18).
• Press (104) under the "synchronised rotate menu change" symbol (166).

The  display  changes  from  the  menu  item  “Synchronised  rotation  menu
change” (166) to “Synchronised rotation until forks in centre position” (169).

Z

The rotary and traverse speeds are pre-set. "Synchronised rotation until forks in
centre position" can be cancelled by releasing the  (104) button. The attachment
must then be moved manually to the home position.

• Synchonised fork carriage 90° rotation and load handler centre traverse:

• Press  and  hold  down  on  the    (104)  button  under  the  "Synchronised  rotation

until  forks  in  centre  position"  symbol  (169)  until  the  attachment  comes  to  rest
and rotary movement stops.

The attachment is in the centre position and the forks are at right angles (90°) to the
truck. Loads can now be lifted from the front.

Z

If  the  attachment  is  not  in  the  centre  position,  you  can  only  travel,  lift  or  lower  at
reduced speed, see page 182.

179

04.19 en-GB

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды