manualshive.com logo in svg

Jungheinrich ESD 220, Руководство по эксплуатации

Поделиться
Скачать
Jungheinrich ESD 220 Скачать руководство пользователя страница 174

02

.1

6 

EN

18

5.2

Operation

5.2.1 Commissioning

Checks and operations to be performed before starting daily work

Procedure

• Make sure the battery is in physically good condition. 
• Make sure the terminals are correct (positive to positive and negative to negative)

and check that contacts on the battery terminal conducting system are secure.

• Check the M10 terminal screws of the conductors and connectors are secure and

if necessary torque to 23 ±1 Nm.

• Charge the battery, see page 18.

The test is now complete.

5.2.2 Discharging the battery

Z

To achieve an optimum useful life avoid operational discharges of more than 60%
of nominal capacity.

Z

If the battery is discharged during operation by more than 80% of rated capacity the
useful  life  of  the  battery  will  reduce  significantly.  Fully  or  partially  discharged
batteries must be re-charged immediately and not left unattended.

5.2.3 Charging the battery

WARNING!

The gases produced during charging can cause explosions

The  battery  gives  off  a  mixture  of  oxygen  and  hydrogen  (electrolytic  gas)  during
charging. Gassing is a chemical process. This gas mixture is highly explosive and
must not be ignited.

Always disconnect the charger and truck before connecting or disconnecting the
charger and battery.

The charger must be adapted to the battery in terms of voltage, charge capacity
and battery technology.

Before charging, check all cables and plug connections for visible signs of damage.

Ventilate the room in which the truck is being charged.

Battery  cell  surfaces  must  remain  exposed  during  charging  in  order  to  ensure
sufficient  ventilation,  see  truck  operating  instructions,  chapter  D,  Charging  the
Battery.

Do not smoke and avoid naked flames when handling batteries.

Wherever an industrial truck is parked for charging there must be no inflammable
material or consumables capable of creating sparks within a minimum distance of
2000 mm from the truck.

Fire protection equipment must be available.

Do not place any metallic objects on the battery.

Always  follow  the  safety  regulations  of  the  battery  and  charger  station
manufacturers.

Содержание ESD 220



























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды