Jungheinrich EJE 220 Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 232

Jungheinrich EJE 220 Скачать руководство пользователя страница 162

4.7

Checking the hydraulic oil level

Checking the hydraulic oil level and
replenishing

Requirements

– Fully lower the load handler.
– Prepare the truck for maintenance and

repairs, see page 154.

Procedure

• Remove the front panel, see page 159.
• Check the oil level in the hydraulic

reservoir (103).

Z

The  hydraulic  reservoir  (103)  has  two
markings  (101).  With  the  load  handler
completely  lowered,  the  hydraulic  oil  level  in
the reservoir should lie between the min. and
max. markings (101).

• Add hydraulic oil if necessary:

• Turn the lid (102) anti-clockwise from the hydraulic reservoir (103).
• Add hydraulic oil of the correct grade until the oil level lies between the

markings (see page 153).

• Turn the lid (102) clockwise on the hydraulic reservoir (103).

• Install the front panel, see page 159.
• To restore the industrial truck to service after maintenance or repair work, see

The hydraulic oil level is now checked.

103

102

101

Z

If a leak is discovered in the hydraulic system (cylinder; unions, lines), the truck must
be decommissioned and repaired by specialist personnel.

4.7.1

Top up the auxiliary hydraulics on the EJE 220r / 225r

Z

The auxiliary hydraulics of the EJE 220r / 225r is a closed system. The auxiliary
hydraulics must only be replaced or topped up by the manufacturer's customer
service department who are specially trained for this task.

Z

Mini measurement connections on the truck should only be used by the
manufacturer's trained customer service department.

162

04.19 en-GB

«
...
160
161
162
163
164
...
»

Содержание EJE 220









































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды