Jungheinrich EJC 14, Руководство по эксплуатации

Страница: 42 / 55

E 11
040
1.G
B
4.4 Safe parking of the truck
If the truck is left unattended, even for only short periods of time, it must be rendered
safe.
f
Do not park the truck on slopes! The lifting device must always be completely lowe-
red.
– Bring control shaft (4) into brake position (B).
– Lowering the lifting device.
– Set key switch (2) to “0” position and remove the key.
– Set master switch (1) to “OFF” position.
4.5 Fault location
This chapter helps the operator to locate and fix simple malfunctions or the results of
operating errors him- or herself. The order of the work stated in the table must be ob-
served for fault location.
f
If it is not possible to rectify the fault by performing the indicated “remedial actions”,
please contact the Customer Service, as more intricate faults can only be rectified by
specially trained and qualified service personnel.
Fault Possible cause Remedy
Truck does not
move – Battery connector
not connected
– Check the battery connector
and reconnect it, if necessary
– Master switch (EMERGENCY
STOP)
pressed
– Release
master switch (EMERGENCY
STOP)
– Key switch set to “0“ position – Set the key switch to position “I”
– Battery voltage too low – Check the charging status of
the battery
and recharge, if necessary
– Control shaft not swivelled into
driving range (F)
– Swivel control shaft into driving
range (F)
– Faulty fuse – Check
fuses F1 and 1F1
– Truck battery charger is con-
nected
– Disconnect the truck battery
charger
from the mains
Load cannot
be lifted – Truck not ready for operation – Perform all troubleshooting
measures that are mentioned
under “truck does not drive”
– Hydraulic oil level too low – Check hydraulic oil level
– Faulty fuse – Check fuse 2F1
– load too high – Pay attention to the maximum
bearing capacity (see identifi-
cation label)
– Discharge monitor is triggered
(STOP icon)
– Check the charging status of
the battery
and recharge, if necessary
E 11
040
1.G
B
4.4 Safe parking of the truck
If the truck is left unattended, even for only short periods of time, it must be rendered
safe.
f
Do not park the truck on slopes! The lifting device must always be completely lowe-
red.
– Bring control shaft (4) into brake position (B).
– Lowering the lifting device.
– Set key switch (2) to “0” position and remove the key.
– Set master switch (1) to “OFF” position.
4.5 Fault location
This chapter helps the operator to locate and fix simple malfunctions or the results of
operating errors him- or herself. The order of the work stated in the table must be ob-
served for fault location.
f
If it is not possible to rectify the fault by performing the indicated “remedial actions”,
please contact the Customer Service, as more intricate faults can only be rectified by
specially trained and qualified service personnel.
Fault Possible cause Remedy
Truck does not
move – Battery connector
not connected
– Check the battery connector
and reconnect it, if necessary
– Master switch (EMERGENCY
STOP)
pressed
– Release
master switch (EMERGENCY
STOP)
– Key switch set to “0“ position – Set the key switch to position “I”
– Battery voltage too low – Check the charging status of
the battery
and recharge, if necessary
– Control shaft not swivelled into
driving range (F)
– Swivel control shaft into driving
range (F)
– Faulty fuse – Check
fuses F1 and 1F1
– Truck battery charger is con-
nected
– Disconnect the truck battery
charger
from the mains
Load cannot
be lifted – Truck not ready for operation – Perform all troubleshooting
measures that are mentioned
under “truck does not drive”
– Hydraulic oil level too low – Check hydraulic oil level
– Faulty fuse – Check fuse 2F1
– load too high – Pay attention to the maximum
bearing capacity (see identifi-
cation label)
– Discharge monitor is triggered
(STOP icon)
– Check the charging status of
the battery
and recharge, if necessary