JUMO TYA S202 Скачать руководство пользователя страница 84

Страница: 84 / 99

8 Error messages and alarms

V1.00/EN/00709725 [Thyristor power controller TYA S202]

The following error messages apply for the entire power controller and are not
divided into master and slave

Master: Malfunction
Thyristor failure

Thyristor defective

The device must be returned to
JUMO for repair.

Return the device

Slave:
thyristor breakage

Master:
Thyristor short circuit

Thyristor defective
Note:
Monitoring only works when the load resis-
tance is so low that at least 10 % of the pow-
er controller nominal current is flowing.

The device must be returned to
JUMO for repair.

Return the device

Slave:
Thyristor short circuit

Master: Caution!
High temperature

Device temperature in the master or slave is
higher than 100 °C
(Excess temperature)

- Ensure adequate ventilation

- Reduce load current

- Use power controller with

higher maximum load current

Slave: Caution!
High temp.

Master: Limit.
active high temp.

Device temperature in the master or slave is
higher than 105 °C
Device is too hot, power is reduced!
(Limited power due to excess temperature)

- Ensure adequate ventilation

- Reduce load current

- Use power controller with

higher maximum load current

Slave: limit.
active high temp.

Master: Mains volt.
too low

Mains voltage is not within specified toler-
ance range

Chapter 10.1 "Spannungsversorgung,
Lüfterkenndaten bei 250A, Laststrom"

Check nominal voltage of the de-
vice type

Chapter 1.3 "Bestellanga-
ben"

Slave: supply volt.
too low

Master: Mains volt.
too high

Mains voltage is not within specified toler-
ance range

Chapter 10.1 "Spannungsversorgung,
Lüfterkenndaten bei 250A, Laststrom"

Check nominal voltage of the de-
vice type

Chapter 1.3 "Bestellanga-
ben"

Slave: supply volt.
too high

Master: Temp drop
in supply

Dangerous temporary DC component for
transformer loads was detected in the master
or slave power controller.

Chapter 5.1.5 "Überwachungen"

Ensure stable mains supply.

Slave: Temp.drop in
mains voltage

Error message

Cause

Remedy

Alarms

Cause

Remedy

Master-slave
rotary field error

-Counterclockwise rotary field was detected
-May also appear if the 1:1 patch cables of
Slave1 and Slave2 are mixed up.

Chapter 3.1.1 "Typ 709066/X-0X-20-
0X-XXX-XX"

Chapter 3.4.1 "Drehstrom
Sparschaltung Master-Slave
für ohmsche Lasten in Stern-
, Dreieckschaltung oder Tra-
folasten (ohmsch-induktiv)"

Master-slave
wiring is wrong.

Wiring fault has been detected

Содержание TYA S202




































































































Результаты поиска

Содержание TYA S202

Отзывы:

Бренды по названию

Популярные бренды

JUMO TYA S202, Руководство по эксплуатации

Результаты поиска

Содержание TYA S202

Отзывы:

Бренды по названию

Популярные бренды