-
.
Technical Specifications
Battery Capacity:
12000 mAh
Battery Life Cycles:
>500
Outputs:
2 x 5V/2.1A, 1 x 12V/10A
Input:
12V/1A
Jump Start Current:
200 - 400A
Dimensions:
6.5” x 2.9” x 1.2”
Bulb Type:
Bright White LED
Bulb Lifespan:
100,000 hours
Bulb Energy Draw:
1 Watt
Bulb Brightness:
86 Lumens
Built-In Protection:
- Overcurrent Protection
- Short-Circuit Protection
- Overload Protection
- Overvoltage Protection
- Overcharge Protection
Troubleshooting
- To charge device from your car, choose the included
DC Car Charger.
- Charging takes 2-3 hours, depending on current
charge levels.
- Once device is fully charged, all Battery Level
Indicators (6) will remain lit.
Note:
While some vehicles can supply a DC charge
even when the engine is off, others cannot. Be sure
to check your vehicle’s manual for specifications, and
check that Battery Level Indicators (6) are showing
the device being charged.
- To check remaining power levels at any time, unplug
all cables from device and short-press the Light
Mode Button (1). Consult the following chart:
Note:
On a full charge, unit’s standby time is about
3 months. It is recommended that the device be
charged once every 3 months to prolong its
service life.
Using the LED Light:
- Press and hold the Light Mode Button (1) for 2
seconds to turn on the flashlight.
- Press and hold again for 2 seconds to switch to the
flashing strobe mode.
- Press and hold again for 2 seconds to switch to
SOS emergency mode.
- Press and hold again for 2 seconds to turn light off.
Charging Mobile Devices:
The two built-in 5V USB ports can charge many
different mobile devices. Use the included USB to
Adapter Cable and choose the adapter made for
your device.
- Connect larger end of USB cable to either of the
USB outputs (5 & 7).
- Select proper adaptor and insert it into smaller end
of USB cable.
- Connect adaptor to mobile device and short-press
Light Mode Button (1) to start charge.
- Both USB outputs may be used simultaneously to
charge separate devices.
- Thanks to an output current that can reach 2A,
most mobile phones will charge to full in just 2 hours,
which is much faster than most factory chargers.
- Once the connected mobile device reaches full
charge, charging will stop automatically.
Jump-Starting a Vehicle:
On a 100% charged battery, the device can power
approximately 20 jump-start sessions. Results may
vary depending on owner usage and vehicle engine
displacement. We recommend using the Mini
Portable Car Jump Starter for vehicles with the
following engine displacements: 4.0 displacement for
gas/petrol-powered vehicles, and 3.0 displacement
for diesel-powered vehicles.
- Ensure that device battery capacity is above 50%.
To check power levels, shortpress Light Mode Button
(1) and check that at least 3 Battery Level Indicators
(6) stay on.
Indicators
All Off
All Flashing
1 On
2 On
3 On
4 On
5 On
Charge
0%
10%
20%
40%
60%
80% 100%
- Connect the included Dual Clamp Jumper Cable to
your vehicle’s battery by placing the red clamp on the
positive “+” terminal and the black clamp on the
negative “-” terminal.
- Insert the cable’s other end into the Jumper Cable
Socket (3).
- Attempt to start the engine. If engine does not start,
wait at least 10 seconds before attempting to start
the engine again.
- After the engine has been successfully started,
disconnect the cable from the Jumper Cable Socket
(3) within 10 seconds.
- For your safety and that of your vehicle, the device is
designed with reverse polarity protection. If you
accidentally connect the red and black clamps to the
wrong polarity terminals and attempt to jump-start the
vehicle, the fuse will blow and cut power immediately
to prevent injury and damage.
Issue
Cause
Solution
All Battery Level
Indicators (6) stay
lit while charging,
but battery is NOT
at maximum
capacity
Device is at about
60% battery
capacity due to
long-term storage
without use
Unplug charging
adapter then
reinsert into DC
Charging Port (4)
No response when
pressing Light
Mode Button (1)
Low Voltage
Protection has
been activated
and electronic
circuit has been
shut off
Plug charging
adapter into DC
Charging Port (4) to
activate electronic
circuit
Quick battery drain
on first use out
of box
Battery requires
full charge prior
to first use
Perform a full
battery drain and
charge for a full 12
hours without use
