Jula 619-231, Руководство по эксплуатации

Страница: 12 / 22

12
2022_001
1 Introduction
1.1 Product description
The product is a roof rack.
1.2 Intended use
The product is intended to be used to transport gods on the roof of cars.
1.3 Symbols
Read the operating instructions carefully and make sure that
you understand the instructions before you use the product.
Save the instructions for future reference.
1.4 Product overview
(Figure 1)
1. Roof rack tube
2. End cap
3. Key
4. Outer protective cover
5. Roof rack bracket
6. Inner protective cover
7. Outer eye bolt
8. Inner eye bolt
9. Protective plate
10. Pressure bracket
11. Lock knob
12. Nut
2 Safety
2.1 Safety definitions
Warning! If you do not obey these instructions, there is a risk of
death or injury.
Caution! If you do not obey these instructions, there is a risk of
damage to the product, other materials or the adjacent area.
Note! Information that is necessary in a given situation.
2.2 Safety instructions for operation
Warning! If you do not obey these instructions, there is a risk of
death or injury.
● Read and understand the instructions before you use the product.
● Save these instructions and safety instructions for future reference.
● Do not use the product for tasks other than its intended purpose. The
manufacturer cannot accept liability for any damage that is a result of
improper use.
● Do not use the product if parts are missing. Speak to the retailer if the
product if parts are missing.
● Do not use the product if it is damaged or is defective. Speak to an
authorized service center.
● Do not repair the product. A damaged or defective product must be
repaired at an authorized service center. The manufacturer cannot accept
liability for any damage that is a result of unauthorized repairs.
● Do not modify the product. The manufacturer cannot accept liability for
any damage or injury that is a result of unauthorized modification.
● Park the vehicle on a level surface before you install the product.
● Make sure that the parking brake in the vehicle is engaged before you
install the product.
● Do not put loads that exceed the maximum permitted load on the
product.
● Make sure that you distribute the load evenly when you put load on the
product. Do not put all the load to the left side or right side.
● Make sure that the product is fully installed before you put load on the
product or operate the vehicle it is installed on. There is a risk of injury
and damage to other people and vehicles if the product comes loose
when you are in traffic.
● Do not open the sunroof on the vehicle when the product is installed.
● Remove the product from the vehicle before you wash the car in an
automatic carwash.
● Examine the product for wear and damage after each operation.
● Do a check of the installation after each operation.
● Avoid sharp braking, sharp acceleration and sharp turns.
● Be extra careful when you use the product in windy conditions.
● Be extra careful when you use the product on roads that are uneven.
● Be aware that the product increases the total height of the vehicle it is
installed on.
● Clean the product regularly.
3 Installation
3.1 To assemble the product
1
Remove all packaging.
2
Unlock and remove the outer protective cover (A). (Figure 2)
3
Pull up the inner protective cover (B).
4
Make sure that the cylindrical part of the lock knob (C) points
upwards. (Figure 3)
5
Make sure that the protective plate (D) is installed to the roof rack
bracket.
6
Install the roof rack tube in the roof rack bracket and install the end
cap to the roof rack tube. (Figure 4)
7
Do a check of the assembled product. (Figure 5)
3.2 To install and remove the product
1
Make sure that the product is assembled correctly. Refer to “3.1 To
assemble the product” on page 12.
2
Put the product on the roof rails of the vehicle and move the pressure
plate until it is between the roof and roof rail on the vehicle. (Figure 6)
Caution! Make sure that the protective plate is attached straight to
the roof rails on the vehicle.
3
Make sure that the outer eye bolt (A) is on the outside of the roof rails.
(Figure 7)
4
Push in the pressure plate until the inner eye bolt is in the cutout in
the pressure plate. (Figure 8)