JUKI PLC-2710NVM Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 40

JUKI PLC-2710NVM Скачать руководство пользователя страница 22

– 20 –

6) Pull the 6-gang switch toward you. Place the thread clamp solenoid cord on the step part. Then, put the 6-gang

switch back into place and secure with the setscrews.

At this time, lightly pull the thread clamp solenoid cord to make sure that it can be moved.

If the cord cannot be moved, it may have been caught under the 6-gang switch. In such a case, remove the

6-gang switch and cord once and re-install them correctly.

8) Remove the cable clip set-

screws. Pass the thread clamp
solenoid cord through the cable
clips and re-secure the cable
clips with the setscrews.

Bundle the cords with a cable
clip band (small).

9) Bundle the cords with the

cable clip band (small).

10) Connect the thread clamp so-

lenoid cord to the thread clamp

solenoid junction cable (asm.) and

route it as shown in the figure.

Bundle the excess length of the

thread clamp solenoid cord togeth-

er with a cable clip band (small).

Fit tge thread clamp solenoid junc-

tion cable (asm.) in the concave

portion of the machine arm.

7) Route the cord to the right side while preventing it

from being caught under the tension disk floating

solenoid and pass it through the notch in the ma-
chine arm.

Notch in the machine arm

«
...
20
21
22
23
24
...
»

Содержание PLC-2710NVM









































Отзывы:

Нет отзывов