JUKI LS-1340 Скачать руководство пользователя страница 5

Страница: 5 / 60

−

Adjustment Procedures

Results of Improper Adjustment

Adjustment Procedures

Results of Improper Adjustment

1. Set the stitch dial to “0 mm”.

2. Remove throat plate and throat plate base.

3. Loosen setscrew

in the feed rocker shaft crank.

4. Loosen setscrew

in the feed rocker shaft rear bushing.

5. Loosen setscrew

in the vertical feed arm.

6. Loosen setscrew

in the vertical feed shaft thrust collar.

7. Loosen setscrew

in the vertical feed rocker shaft bushing.

8. Turn the handwheel to bring the needle bar to the lowest dead

point of its stroke.

9. Move the feed rocker shaft bushing and the vertical feed rocker

shafdt bushing. Slightly move horizontal feed base

and feed

base

, and adjust so that needle

enters in the center of

the needle hole of feed dog

. (a = a’)

10.After the adjustment, securely tighten the setscrews.

When the height of the feed dog is

higher than the specified value :

™

Stitch pitch becomes larger than

the scale of the feed dial.

™

Balloon stitches will result.

™

Return of sewing product will

occur.

When the height of the feed dog is

lower than the specified value :

™

Stitch pitch becomes smaller

than the scale of the feed dial.

™

Feed force will be deteriorated.

™

S t i t c h s k i p p i n g o r t h r e a d

breakage will result.

™

Poorly tensed stitches will result.

™

Needle breakage will result.

1. Set the stitch dial to “0 mm”.

2. Turn the handwheel to bring the height of the feed dog to the

maximum.

(Bring the needle bar to the lowest dead point of its stroke.)

3. Loosen setscrew

in the vertical feed bar shaft arm, move

feed base

up or down and adjust feed dog

from top surface

of the throat plate (center section) to the dimension A. Then

securely tighten the setscrew.

Содержание LS-1340





























































Результаты поиска

Содержание LS-1340

Отзывы:

Похожие инструкции для LS-1340

Бренды по названию

Популярные бренды

JUKI LS-1340, Руководство пользователя

Результаты поиска

Содержание LS-1340

Отзывы:

Похожие инструкции для LS-1340

Бренды по названию

Популярные бренды