manualshive.com logo in svg

JUKI LBH-1790A Series, Инструкция по эксплуатации

Поделиться
Скачать
JUKI LBH-1790A Series Скачать руководство пользователя страница 73

– 70 –

Error code

Description

How to recover

Place of recovery

E499

Presser size error (Length direction : rear)

When stitching data exceeds the size of rear of length 

direction of presser.

Possible to 
re-enter after 
pressing reset 
key.

(During individual sewing/
cycle sewing)
Sewing data edit screen
[S002] Cloth cut length
(During continuous sewing)
Standard screen

E703

Panel is connected to the machine other than 

supposed. (Machine type error)

When machine type code of system is improper in case 
of initial communication.

Turn OFF the 
power.

E704

Nonagreement of system version

When version of system software is improper in case 
of initial communication.

Turn OFF the 
power.

E730

Main shaft motor encoder defectiveness or phase-

out

When encoder of sewing machine motor is abnormal.

Turn OFF the 
power.

E731

Main motor hole sensor defectiveness or position 

sensor defectiveness

When hole sensor or position sensor of sewing 
machine motor is defective.

Turn OFF the 
power.

E733

Reverse rotation of main shaft motor

When sewing machine motor rotates in reverse 
direction.

Turn OFF the 
power.

E801

Phase-lack of power

When phase-lack of input power occurs.

Turn OFF the 
power.

E802

Power instantaneous cut detection

When input power is instantaneously OFF.

Turn OFF the 
power.

E811

Overvoltage

In the case the input power source voltage/current is 

equal to or more than the specified value

Turn OFF the 
power.

E813

Low voltage

In the case the input power source voltage/current is 

equal to or less than the specified value

Turn OFF the 
power.

E901

Abnormality of main shaft motor IPM

When IPM of servo control p.c.b. is abnormal.

Turn OFF the 
power.

E902

Overcurrent of main shaft motor

When current flows excessively to sewing machine 

motor.

Turn OFF the 
power.

E903

Abnormality of stepping motor power

In the case the stepping motor power of the servo-

control PCB is out of the range of the specified values

Turn OFF the 
power.

E904

Abnormality of solenoid power

In the case the solenoid power of the servo-control 

PCB is out of the range of the specified values

Turn OFF the 
power.

E905

Abnormality of temperature of heat sink for servo 

control p.c.b.

When temperature of heat sink of servo control p.c.b. 

is 85˚C or more.

Turn OFF the 
power.

E906

Main PCB heat sink temperature fault

In the case the temperature of the heat sink of the main 

PCB increases

Turn OFF the 
power.

E907

Stitch width motor origin retrieval error

When origin sensor signal is not inputted at the time of 
origin retrieval motion.

Turn OFF the 
power.

Содержание LBH-1790A Series
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды