JUKI DDL-8700A-7 Скачать руководство пользователя страница 52

Страница: 52 / 60

– 49 –

16. connection of the material end sensor

) Open the cover referrng to

-13. removing

the rear cover" p.46

2) Connect the connector of materal end sensor to

connector

(CN54 : 4P).

3) Assgn CN54 to the materal end sensor nput

referrng to

-8-

. Selection of the optional

input/output function (Function setting No.

12) p.34

4) To use the materal end sensor, set up the sen-

sor functons on the control box through the

functon settng procedure. Selectable functons

and the correspondng selecton numbers are as

follows:

・

Materal end sensor functon (functon settng No. 2)

The materal end sensor s enabled.

0: Materal end sensor s not used.

: Materal end sensor s enabled.

・

Thread trmmng functon by means of the mate-

ral end sensor (functon settng No. 3)

The automatc thread trmmer s actvated after

the detecton of the materal end.

0: Automatc thread trmmng s not carred out.

: Automatc thread trmmng s carred out.

・

The number of sttches after the actvaton of the

materal end sensor (functon settng No. 4)

The number of sttches to be sewn untl the sew-

ng machne stops after the materal end sensor

has detected the material end can be specified.

Data settng range: 0 - 9 </sttch>

・

One-shot functon (functon settng No. 76)

The one-shot operaton untl the materal end s

detected can be set.

0: One-shot operaton s not carred out.

: One-shot operaton s carred out.

(caution) 1. Be sure to turn oFF the power before

connecting the connector.

2. For the use of the material end sen-

sor, refer to the Instruction Manual

attached to the material end sensor.

JUKI genune part number Connector

HK04230040

Pn contact

HK042340000

7 6

Pn No.

Sgnal name

Remarks

+12V

Power supply s selected

accordng to the sensor

used.

+5V

OPT_S

Sensor nput s assgned to

the materal end sensor.

GND

Содержание DDL-8700A-7





























































Результаты поиска

Содержание DDL-8700A-7

Отзывы:

Похожие инструкции для DDL-8700A-7

Бренды по названию

Популярные бренды

JUKI DDL-8700A-7, Инструкция по эксплуатации

Результаты поиска

Содержание DDL-8700A-7

Отзывы:

Похожие инструкции для DDL-8700A-7

Бренды по названию

Популярные бренды