background image

Operation

The degree of contamination and cleaning

process can be observed from the outside.

INFO_NO_HEADER

The device is backwashed with

filtered water. The filtered water

supply of the domestic installation

remains intact during the backwash-

ing process. No dirty water can reach

the pure water side during the back-

washing.

4.2.1 Backwashing interval

If cleaning is not performed soon enough,

the result may be damage to the sieve

insert. Large quantities of filtered particles

can deform the sieve fabric and in extreme

case lead to tearing of the sieve fabric.

In addition, larger deposit quantities can

impair the backwashing function mechani-

cally.
According to DIN EN 13443-1 backwashing

the device is required at the latest every six

months.

The manufacturer recommends a back-

washing:

at least every 2 months

if the water pressure drops

if the filter is visibly dirty

Experience has shown that new installa-

tions in the early stages of installation lead

to increased dirt deposits. In this case, a

more frequent backwashing is necessary.

4.2.2 Due date of backwashing

Every two months, a beep reminds you that

the backwashing is due.
To switch off the beep, press the reset but-

ton on the handwheel cover.

By pressing the button, the time interval

of 2 months is restarted.

The signal is just an additional reminder

of the necessary backwashing. Indepen-

dant from this signal, the backwashing

interval indicated in chapter 4.2.1 must be

observed.

Check backwash reminder alarm

Press the reset button for at least 3 sec-

onds:

Beep:

 the backwash reminder alarm

works. The batteries still have enough

capacity.

No beep:

 replace the batteries by new

leak-proof batteries.

This battery test has no influence on the

backwashing interval.

Replace batteries of the backwash

reminder alarm

1.

Remove the handwheel cover.

2.

Replace the batteries in the battery

compartment by new ones of the same

type (AAA or LR03).

3.

Refit the handwheel cover.

4.

Press the reset button on the hand-

wheel cover for at least 3 seconds. The

time interval of two months is restarted.

Attention:

 do not dispose of used batter-

ies with the household waste, but in accor-

dance with the local waste disposal regula-

tions.

12

JUDO JPM+ 

1702272 • 2020/07

Содержание 8170200

























Отзывы: