JST CMKS-L Скачать руководство пользователя страница 29

Страница: 29 / 31

JST

CMKS-L INDUSTRY STANDARD APPLICATOR

H:\0 - Quality Documents\2 Department\Tech Serv\Application tooling\Applicators and Die sets\TS174-00

CMKS-L Manual.doc

4.9 The wire must be crimped at the correct position.

The conductors do not protrude enough. (The wire easily comes off due to

incomplete crimping).

The conductors protrude excessively. (The conductors interfere with the tightening

nut, preventing the terminal from being installed).

The wire insulation is crimped at the wire barrel. (Poor conduction or breakage due

to excessive crimping will occur).

The wire insulation is not completely crimped at the insulation barrel. (The wire

insulation easily comes out from the insulation barrel).

The conductors and wire insulation are visible.

The conductors must protrude 0.5 to 1.0 mm.

Содержание CMKS-L
































Результаты поиска

Содержание CMKS-L

Отзывы:

Похожие инструкции для CMKS-L

Бренды по названию

Популярные бренды

JST CMKS-L, Руководство по эксплуатации

Результаты поиска

Содержание CMKS-L

Отзывы:

Похожие инструкции для CMKS-L

Бренды по названию

Популярные бренды