manualshive.com logo in svg

JRC Alphatron Marine AlphaTurn, Инструкция по установке и эксплуатации

Поделиться
Скачать
JRC Alphatron Marine AlphaTurn Скачать руководство пользователя страница 17

For pin connections, see Figure 10: Serial pin connections on page 17, Table 4: Serial Connector P12 (8 pins) on
page 17 and Table 5: Serial Connector P19 (12 pins) on page 17.

Figure 10: Serial pin connections

1

COM0

IEC 61162-2 Tx+

2

COM0

IEC 61162-2 Tx–

3

COM0

IEC 61162-2 GND

4

COM0

IEC 61162-2 Rx+

5

COM0

IEC 61162-2 Rx–

Table 4: Serial Connector P12 (8 pins)

1

COM1

IEC 61162-1 Tx+

2

COM1

IEC 61162-1 Tx–

3

COM1

IEC 61162-1 Rx+

4

COM1

IEC 61162-1 Rx–

5

COM2

IEC 61162-1 Tx+

6

COM2

IEC 61162-1 Tx–

7

COM2

IEC 61162-1 Rx+

8

COM2

IEC 61162-1 Rx–

9

COM3

IEC 61162-1 Tx+

10 COM3

IEC 61162-1 Tx–

11 COM3

IEC 61162-1 Rx+

12 COM3

IEC 61162-1 Rx–

Table 5: Serial Connector P19 (12 pins)

Note  The instrument should always be connected according to the cable diagram. See Electric Diagrams on
page 51. Ensure connection to the correct COM port.

1.1.13 Relay

One relay output is available for legacy alarm monitoring systems without serial ALR connection. This AlphaLine
instrument relay output is located on the 8-pin connector on the following pins. Use the NC (Normally Closed), or NO
(Normally Open) connection depending on the application.

For pin lay out, see Table 6: Relay Connector P12 (8 pins) on page 18.

17  |  Installation Instructions

Содержание Alphatron Marine AlphaTurn


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды