Joysway Hobby OFFSHORE LITE WARRIOR V4 Скачать руководство пользователя страница 4

4

DRIVING YOUR OFFSHORE LITE SERIES

1) Switch ‘ON’ the transmitter. Check that the transmitter’s red LED glows brightly. 
2) Check that the Offshore Lite Warrior ‘s turn fins are adjusted correctly.
3) Switch ‘ON’ the Offshore Lite  Series (connect the 7.2V Power Pack).
4) Check that the propeller and the rudder respond to transmitter inputs before placing the Offshore Lite Series
     on the water.      

AFTER USE

1) When you have finished using your Offshore Lite Series, you should first switch ‘OFF’ the model (disconnect
     the 7.2V Power Pack), then switch ‘OFF’ your transmitter.     
2) Remove all batteries from the transmitter and model.
3) Leave the Offshore Lite Series’s upper deck off to allow moisture to evaporate. Ideally, place the model in this
     way in a warm and dry place, like an airing cupboard, until you are sure it is dry and then store it away. 
4)  Remove the rubber ring from the slot of hull, so as to keep the rubber ring flexible for water proof effective 
      in next time boat racing. 

NOTE: If the Offshore Lite Series begins to bob when running, it may have taken on an excessive amount of

water. In this case, you should immediately return to shore, remove the upper deck and drain the water 
from the hull. 

IF THE OFFSHORE LITE SERIES DO NOT RUN IN A STRAIGHT LINE 

If your Offshore Lite Series do not run in a straight
line when not being steered, you can adjust it by 
using the steering trim located on the upper right 
hand side of the transmitter.   

1) Run your Offshore Lite Series on calm water
when adjusting the steering. If your model runs 
to the right when not being steered, press the
 “ST.TRIM-L” button. Re-center the model and
 see if this has corrected the problem. Keep 
making small adjustments in this way until the 
model runs stright.

Press the “ST.TRIM-R” button to correct if your 
model steers to the left without being steered
in the same way as detailed above.

ST.TRIM-L

ST.TRIM-R

TURN FINS

The Offshore Lite Warrior V4 features adjustable turn
fins to aid in turning. These can be adjusted using the 
included Allen key. The optimum angle of 
adjustment is 45 degrees to the hull.  

Offshore Lite Warrior V4 /Sea Rider V5 RTR Mini EP Racing Boat

Содержание OFFSHORE LITE WARRIOR V4







Отзывы: