Joraform Installation Instruction SE/UK JK125/270 180831
Joraform AB
English
4
A
Insert plastic pipe M on plastic pipe D.
B
Insert gable E on D. Painted surface of the gable shall be downwards.
C
Insert insulation Fa on D. Painted surface of the gable shall be upwards. Insert plastic
plate Ka on D. Note that the ventilation holes in the insulation material and plastic plate
must be in line with ditto in steel gable E.
D
Insert plastic pipe L on D.
E
Insert plastic plate Kb on D.
F
Insert insulation Fb on D.
G
Insert plastic plate Kb on D. Mount the plastic screws V and nuts U in the holes of the
plastic plates: Push the plastic screws by force through the insulation. Tighten the nuts until
insulation compresses approx. 5mm.
H
Insert plastic pipe L on D.
I
Insert plastic plate Ka on D.
Insert insulation Fa on D.
J
Insert gable E on D, note that the ventilation holes in the insulation and plastic plate
material must be in line with the ditto in steel gable E. Painted surface of the gable shall be
upwards.
K
Insert plastic pipe M on D.
L
Mount the other A+R on B.
M
Fasten one end of the flat rod R to the un-mounted A, use nut J and screw P. Note that
the locations of holes are not symmetrical on A.
N
Mount locking nuts J on the treads on rods B, use only hand-force, don’t use any tools
for tightening yet.
O
Raise the compost on the stand carefully.
P
Tighten locking nuts J rather hard, use 2pcs spanner 13 mm or a 2 pcs adjustable
spanners. Best result will be achieved if 2 persons help each other to tighten the locking
nuts!
Now we recommend you to lay down the becoming compost barrel on the ground (like in
sketch 5 and 8), it really simplifies the mounting of all the lids and diagonal flat rod in the
next coming chapters. Don’t forget though to protect the painted surfaces from damages,
please work on a soft base.
A
Mount locking nuts J on one side of the threaded rods B. Tighten them only by hand-
force, don’t use tools to tighten. (Remove any plastic covers protecting the threads first).
B
Fasten one end of the flat rod R to one of the A stands, use nut J and screw P. Note that
the location of all holes on A are not symmetrical.
C
Insert the threaded rods B in the holes on A+R, with the nuts downwards.
2
Insert steel pipes C in threaded rods B.
3
Insert the long plastic pipe D over one of pipe C. (see also sketch 1-3).
A
Mount the double lid Ha with self-threading screws X. Turn the double lid Ha so that you
are having the handles facing against you, when you have the mounting holes in A in the
back (see sketch 5 and 8). Easiest if one pushes downwards and one uses the
screwdriver. Fitting on the isolation can vary depending on the age of it, it may shrink a little
bit by time. Adjust octagonal isolations so they are in the correct position and not over the
ventilation holes. (Turn them around the center axle).
B
Mount lid with the excenter lock (Hd) beside double lid (Ha). Turn it so the excenter locks
match each other.
C
Mount the lids Ha and Hb so you get the handles symmetrically placed around the
compost, use the self-threading screws X, and don’t tighten them hard! When all lids are
mounted, then tighten the screws.
6/7
Insert the plastic screws V through the holes in steel gable E and press them with force
through the insulation Fa. Use plastic washer T and plastic nut U on the inside.
Notice! Ventilation hole in steel gable E must be in line with the ditto in insulation
Fa and plastic plate Ka
(also see sketch 6 and 7).
8
Mount diagonal flat rod Q, use nut J (4pcs) and screw P (4pcs).