Jonsered FR2312 MA Скачать руководство пользователя страница 25

Страница: 25 / 32

English

– 25

Troubleshooting schedule

Problem

Cause

Engine does not start

There is no fuel in the fuel tank

Faulty spark plug.

Defective ignition cable.

Dirt in the carburettor or fuel line

Starter motor does not turn over the engine

Defect safety switch

Starter motor does not turn over the engine

Battery flat

Bad contact between the cable and battery

Lift lever for cutting unit in wrong position

Main fuse blown.

Ignition lock faulty

Brake not activated.

Faulty starter motor

Engine does not run smoothly

Faulty spark plug.

Carburettor incorrectly set

Air filter clogged

Fuel tank vent blocked

Ignition key defective

Dirt in the carburettor or fuel line

Choking or incorrectly adjusted throttle cable

Engine seems to have no power

Air filter clogged

Faulty spark plug.

Dirt in the carburettor or fuel line

Carburettor incorrectly set

Choking or incorrectly adjusted throttle cable

Engine overheats

Engine overloaded

Faulty spark plug.

Air intake or cooling flanges blocked

Fan damaged

Too little or no oil in engine

Ignition faulty

Battery does not charge

One or more battery cells faulty

Poor contact on the battery terminal cable connectors

Machine vibrates

Blades are loose

Engine is loose

One or more blades unbalanced, caused by damage or poor balancing after
sharpening

Uneven mowing

Blades blunt

Long or wet grass

Cutting unit skew

Grass blockage under hood

Different tyre pressures on right and left sides

Over-speeding

Engine speed too low

Drive belt slipping

Содержание FR2312 MA

































Результаты поиска

Содержание FR2312 MA

Отзывы:

Похожие инструкции для FR2312 MA

Бренды по названию

Популярные бренды

Jonsered FR2312 MA, Руководство оператора

Результаты поиска

Содержание FR2312 MA

Отзывы:

Похожие инструкции для FR2312 MA

Бренды по названию

Популярные бренды