Jonsered 1188S CE Скачать руководство пользователя | Manualshive

Страница: 62 / 96

background image

DANGER

Be especially careful when working near electricity lines. Also beware of overhead
lines for electrified rail roads. Maintain a distance of at least five meters.

If an accident occurs

- do not touch metallic parts of the crane (the stabiliser legs will ground the crane,
and you will be connected to an electric circuit).

- warn others, ask them to move farther away, forbid them from touching the load,
crane, vehicle or ground near the crane

- request that power is turned off from the electricity line.

10.2. Slope control [option]

A slope indicator is placed on the crane base to monitor the
tilting of the crane . When the tilt of the crane exceeds the
angle  permitted,  a  dump  valve  is  activated  and  the  crane
switched to idling. All load increasing actions will be stoped
until the situation is over. During this period it is possible to
operate  an  appropriate  crane  function  to  correct  the
situation.  See  picture.  Press  the  stop  button  while  moving
the lever.

10.3. Adjust the speed of each function for TimberTronic
control system

At start up, the system by default is set to full speed. To
reduce the speed of each function, use an Allen key and a
screwdriver to adjust the screws.

During operation

62

Jonsered 1188S CE

«
...
60
61
62
63
64
...
»

Содержание 1188S CE

































































































Отзывы:

Нет отзывов

Похожие инструкции для 1188S CE

Бренд: Campbell Страницы: 18

Бренд: Vector Страницы: 4

Бренд: NORLUX Страницы: 2

Бренд: OfiTE Страницы: 21

Бренд: Earthlite Страницы: 4

Бренд: YATEK Страницы: 78

Бренд: Landoll Страницы: 34

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: dbx Страницы: 2

Бренд: Eagle Group Страницы: 8

Бренд: Gatekeeper Страницы: 8

Bure Rise & Go DB 56-309

Бренд: Gate Страницы: 8

Бренд: JB-Lighting Страницы: 32

Бренд: W&H Страницы: 72

Бренд: KaVo Страницы: 4

ORTHOPANTOMOGRAPH OP 3D

Бренд: KaVo Страницы: 40

KEY Laser III 1243

Бренд: KaVo Страницы: 103

EXTRAmatic 9040

Бренд: KaVo Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды