Jonsered 1188S CE Скачать руководство пользователя

Страница: 59 / 96

9.4.1. Stabiliser system and ground conditions

Always:

• Make sure that the ground can support the load that

the stabiliser leg imposes on the ground.

(*)

• Make sure that the ground is not undermined.
• Use the extra support plates that are large and firm

enough for your crane model.

The maximum permitted ground inclination under
the stabiliser leg plate is 5º.

(*) The maximum load that the stabiliser leg can impose on the ground:

Jonsered

P (kN)

1100R, 1300R, 1088S, 1188S, 1420S, 1250Z, 1400Z, 1500Z

165

Separate stabiliser beam

B5500

P (kN)

ET450

P (kN)

SY550

P (kN)

1620Z

165

220

355

2490S, 2850S, 2640Z

220

355

NOTE

Sign that shows the maximum force that the stabiliser
legs can apply to the ground.

Starting crane operation

Jonsered 1188S CE

Содержание 1188S CE

































































































Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды

Jonsered 1188S CE, Руководство оператора

Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды