MKA-32 Quick Release Bracket
Installation Instructions:
1.
Remove both side covers (marked [A] in the illustration).
2. Remove Pin [12] and open Cam Lever [7]. Remove the Top Plate [10] from the Base Plate [11].
3.
Use the (6) 1/4” x 5/8” Screws to fasten the Top Plate to the bottom of the motor base extrusion.
Note:
For Ulterra motors use the hex head screws and clipped washers that came with the Ulterra.
4. Re-install both side covers. Assemble the motor and Top Plate onto the Base Plate and latch the Cam Lever.
5.
Positioning the motor/quick release bracket for mounting location:
A: For PowerDrive or Terrova motors: Fully deploy the motor and position the bracket/motor on
the bow of your boat to check for proper clearance (the motor, as it is lowered into the water or
raised into the boat must not encounter any obstructions.)
B: For Ulterra motors: Postion the bracket/motor so the notch in the base is aligned with the
rubrail of the boat (for proper clearance the entire notch must be visible beyond the rubrail, as
shown to the right.)
6. Mark the side edges and rear of the Base Plate on the bow of your boat. Open the Cam Lever
and remove the Base Plate. Reposition the Base Plate to the marks. Locate and mark the (6)
mounting holes in the Base Plate and drill the holes to 9/32” diameter. Fasten Base Plate to the
bow using (6) 1/4” x 2” Flat Head Screws, (6) Fender Washers and (6) Lock Nuts.
Note:
Mounting surface for Base Plate must be completely flat. Washers must be used to shim
base plate flat before hardware is tightened. Top Plate will not fit correctly unless Base Plate is installed completely flat.
7.
Install motor/Top Plate to Base Plate and latch Cam Lever.
8. Your motor is now mounted. Always check that the Cam Lever is latched always use Pin [12] to ensure cam lever remains latched.
9. Cover [16] is available to use when motor is not mounted on the boat. To install the cover, lay cover on top of base plate, apply down pressure to the
center of the Cover while latching the Cam Lever. Cover should fit snug to the Base Plate.
1
2
11
10
9
6
14
7
15
5
12
13
8
4
3
16
Item #
QTY.
Part #
Description
1
1
2222716
Spring, Compression
2
1
2223205
Stop, Draw Bar Quick Attach
3
1
2223452
Screw, 1/4 x 3/4 AB
4
1
2223605
Draw Bar Quick Attach Plate
5
1
2225110
Pad, Urethane
6
1
2228412
Cam Puck
7
1
2228415
Cam Lever
8
1
2262635
Pin Roller
9
1
2371937
Plate, Backer
10
1
2371986
Plate, Top
11
1
2371996
Plate, Base
12
1
2372623
Pin, w/Ring
13
1
2372644
Roll Pin
14
1
2373428
Screw 5/16-18 x 3/4”
15
1
2373650
Lanyard, Plastic
16
1
2770245
Cover, Quick Release Plate
n
1
2994863
Bag Assembly, Includes:
6
2332104
1/4” x 5/8 Screw
6
2223446
Flat Head 1/4” x 2” Screw
6
2263103
1/4” Lock Nut
6
2261713
1/4” Washer
For Use with all PowerDrive, Terrova and Ulterra Trolling Motors.
Kit Includes:
A
Ulterra Alignment
A
For warranty information please visit www.minnkotamotors.com
A Johnson Outdoors Company
Minn Kota Consumer & Technical Service
Johnson Outdoors Marine Electronics, Inc.
PO Box 8129
Mankato, MN 56001
121 Power Drive
Mankato, MN 56001
Phone (800) 227-6433
Fax (800) 527-4464
minnkotamotors.com
©2018 Johnson Outdoors Marine Electronics, Inc.
All rights reserved.
Part #2377116
Rev J
03/18
ECN 38744
*Terrova example shown
See Ulterra Owner’s Manual for
additional mounting options
