Johnson Fitness T8000E Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 35

Johnson Fitness T8000E Скачать руководство пользователя страница 30

30

[Symptom]
Press start then maintenance lamp will light “RED”, when the “ERROR Log-

ERROR 3 or 6” will show the 01.

[Cause]
1. The 8-pin console cable is damaged.
2. Incline motor is damaged.
3. TV is damaged.
4. MCB is damaged.
5. The incline setting is not correct.
[Solution]

1. Please check the incline motor cable whether to inset MCB.

2. Check the console signal whether transmission to MCB, you can refer to MCB

LED UP and DOWN. If LED not light please check the console cable and

console. If LED have light please replace the incline motor

3. If “ERROR Log- ERROR 3 or 6” still show the 01, please replace the incline

motor.

4. If “ERROR Log- ERROR 3 or 6” still show the 01, please replace the TV.

5. If “ERROR Log- ERROR 3 or 6” still show the 01 , please replace the MCB.

6. Enter Engineering Mode to renew the

Auto-calibration( Engineer mode P15)

.

Error message 3,6 troubleshooting

MCB LED UP and DOWN LED

whether have light.

«
...
28
29
30
31
32
...
»

Содержание T8000E




































Отзывы:

Нет отзывов