background image

Caution

Wipe the units with a dry soft cloth, or a cloth slightly moistened with water or cleaner (not with

volatile liquid such as thinner or gasoline). 

 

Note: 

Remove the front panel. 

 

Disconnect the power supply before cleaning and maintenance.

Do not splash water on the units for cleaning, as electric shocks may

 occur

.

Dip a piece of cloth into the water colder than 45

and dry it.Then wipe

the dirty part of front panel.
Note: Do not immerse the front panel into water so as to protect microcomputer components and circuit 

diagram on the front panel. 

Do not to touch the fin of indoor unit during cleaning to avoid personal injury.

Clean and care

14

Clean the air filter

Take down the air filter

Lift up the front panel.

Pull the air filter downwards to take it off,

as shown in

 

Fig.(a, b).

Use a vacuum cleaner to remove dust.

If the filter are dirty, wash them with warm water

and a mild detergent.

Dry the filters in the shade.
Note: Never use water above 45

 to clean the air

 

 

filter or it can cause deformation or discoloration. 

Reinstall the air filter

Reinstall the filters along the direction of arrowhead.

Close the panel.

Cleaning  the Air Filter (every 3 months)

Cleaning the Front Panel 

(

a)

(

b)

Содержание YORK YWHJZH009BAMXAFX





































Отзывы: