Johnson Controls YORK OPTIVIEW CONTROL CENTER Скачать руководство пользователя страница 121

Страница: 121 / 142

JOHNSON CONTROLS

121

SECTION 4 - PRINTERS

FORM 160.10-O1

ISSUE DATE: 4/27/2018

PRINTER CONNECTIONS

Connect the listed printers to the control center mi-

croboard as follows. Only one printer can be connected

at a time.

TABLE 10 -

OKIDATA 182, 182 TURBO, 184 TURBO

PRINTER CONNECTIONS

MICROBOARD

PRINTER

FUNCTION

J2-4

pin 3

Tx (data to printer)

J2-2

pin 11

DSR (busy signal from
printer)

J2-9

pin 7

Gnd

Cabinet

Shield

TABLE 11 -

WEIGH-TRONIX PRINTER

CONNECTIONS

MICROBOARD

PRINTER

FUNCTION

J2-4

pin 2

Tx (data to printer)

J2-2

pin 5

DSR (busy signal from
printer)

J2-9

pin 7

Gnd

Cabinet

Shield

TABLE 12 -

SEIKO PRINTER CONNECTIONS

MICROBOARD

PRINTER

FUNCTION

J2-4

pin 3

Tx (data to printer)

J2-2

pin 8

DSR (busy signal from
printer)

J2-9

pin 5

Gnd

Cabinet

Shield

Hardware Required:

Cable

#18 AWG stranded 50 ft. maximum length.

Connectors

Microboard

• None. Strip 1/4" insulation from wire and insert

into screw terminal block.

Printers

• Okidata - 25 pin plug DB-25P or equivalent; Shell

DB-C2-J9 or equivalent.

• Weigh-Tronix - Same as Okidata. Cable assembly

available from Weigh-Tronix.

• Seiko - 9-Pin D-type Subminiature (DB-9 pin

male).

PRINTER SETUP

The selected printer must be configured as follows. Re-

fer to manual provided by Printer manufacturer with

the respective Printer.

OKIDATA 182, 182 turbo, 184 turbo Printer

CONTROL BOARD Switch settings:

Unslashed 0

off

Unslashed 0

off

Unslashed 0

off

Form Length 11 in.

off

Auto Line Feed off

8 bit data

off Enable front panel

If equipped with a SUPER SPEED serial Board:

1-1

Odd or even parity

1-2

No parity

1-3

8 bit data

1-4

Protocol ready/busy

1-5

Test select

1-6

Print mode

1-7

off

SDD(-) pin 11

1-8

SDD(-) pin 11

2-1

1200 Baud*

2-2

1200 Baud*

2-3 off 1200

Baud*

2-4 off DSR

active

2-5

Buffer threshold 32 bytes

2-6

Busy signal 200ms

2-7

DTR space after power on

2-8

Not Used

If equipped with HIGH SPEED serial board:

off

(-) Low when busy

off

1200 Baud*

off

1200 Baud*

Содержание YORK OPTIVIEW CONTROL CENTER















































































































































Результаты поиска

Содержание YORK OPTIVIEW CONTROL CENTER

Отзывы:

Похожие инструкции для YORK OPTIVIEW CONTROL CENTER

Бренды по названию

Популярные бренды

Johnson Controls YORK OPTIVIEW CONTROL CENTER, Руководство по эксплуатации

Результаты поиска

Содержание YORK OPTIVIEW CONTROL CENTER

Отзывы:

Похожие инструкции для YORK OPTIVIEW CONTROL CENTER

Бренды по названию

Популярные бренды