Johnson Controls VMA18 Series, Руководство по установке

Страница: 13 / 26

Sensor replacement and reuse
scenarios table
Table 3: Sensor replacement and reuse scenarios
Sensor used with VMA1410, VMA1415,
VMA1420, VMA1440 Controller
Sensor replacement and reuse scenarios Instructions
Replace a sensor with an NS Series Sensor
Note: Replacing a TE-6xxx Series
Sensor is recommended over reusing
the sensor because it provides a
usable port at the sensor location for
commissioning.
Replacing a TE-6xxx series sensor
TE-6xxx Series (see TE-6xxx series sensor
connected to VMA Controller )
Note: The VMA1832 does not support
the Dual Setpoint model TE-67xP-3x00
Reuse a sensor, installing an adapter at a
VMA controller location
Reusing a TE-6xxx series sensor
AP-TMZ1600-0 (see Replacing an AP-
TMZ1600-0 sensor connected to a VMA
Controller )
Replace a sensor with an NS Series Sensor
Replacing an AP-TMZ1600-0 sensor
connected to a VMA Controller
TE-7710-0 Series Wireless Transmitter and
TE-7720-0 Wireless Receiver (see Replacing
a TE-7710-0 Series Wireless Transmitter and
TE-7720-0 Wireless Receiver connected to a
VMA Controller )
Replace with a WRZ Series Wireless Sensor
and aWRZ7860 Series One-to-One Receiver
Replacing a TE-7710-0 Series Wireless
Transmitter and TE-7720-0 Wireless Receiver
connected to a VMA Controller
Replace a sensor with a TE-730 Series Sensor
Replacing a TE-700 Series sensor
TE-700 Series (see TE-700 Series Sensor
connected to a VMA Controller )
Reuse a sensor
Reusing a TE-700 Series sensor
Sensor Replacement Scenario
Descriptions
TE-6xxx series sensor connected to
VMA Controller
To replace a TE-6xxx Series Sensor with a
functionally equivalent NS Series Network Sensor,
follow the instructions in the Replacing a TE-6xxx
series sensor section.
To reuse a TE-6xxx Series Sensor connected to
a VMA controller, follow the instructions in the
Reusing a TE-6xxx series sensor section.
Replacing the sensor with an NS Series Network
Sensor is preferred to reusing the TE-6xxx Series
Sensor because the NS sensor allows for easier
controller commissioning. Be sure to use an NS
sensor with similar dimensions as the existing
sensor in order to match the original sensor
installation.
Note: If temporary occupancy is required for
the application on the TE-67xx and TE-68xx
Series Sensors, set the sensor's LED mode to
LED ON (the DIP switch positions on the back
of the sensor are down, up, and down). This
setting only applies to single and no setpoint
controller models (not dual setpoint controller
models). The VMA1832 does not support the
LED OFF mode and the pushbutton will not
function in that configuration.
Refer to the NS Series Network Sensors Product
Bulletin (LIT-12011574) for a complete list of available
NS Series Network Sensors.
Note: In each of the following procedures
that include the use of the Commissioning
Converter (BTCVT), note the following: The
Mobile Access Portal (MAP) Gateway serves
as a replacement for the BTCVT, which is no
longer available for purchase, but continues to
be supported on select controllers. CCT auto-
detects when BTCVT can be used or not, based
on the controller model and the corresponding
CCT Release mode.
• BTCVT can be used with controllers that
contain CCT Release mode 10.2 or earlier
firmware.
Metasys
®
controllers from Release 9.0 or
earlier support BTCVT.
• BTCVT cannot be used with controllers that
contain CCT Release mode 10.4.
VMA1826/1832 VAV Controller Installation Guide 13