Johnson Controls VFD66JCB-1 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 22

Johnson Controls VFD66JCB-1 Скачать руководство пользователя страница 21

Installation Guide

21

Issue Number: 2

www.johnsoncontrols.com

O

pe

ra

tio

n

Me
cha
nical
inst
all

E

Op
er

at

io

n

Te

U

7

UL listing information

7.1 UL information

(For VFD66JCB-1, VFD66KCB-1)

The Johnson Control UL file number is E244421. Confirmation of UL listing can be found on the UL
website: www.ul.com.

7.1.1

Conformity

The drive conforms to UL listing requirements only when the following are observed:

•

Class 1 60/75°C (140/167°C) copper wire only is used in the installation.

•

The ambient temperature does not exceed 50°C (122°F) when the drive is operating.

•

The grounding connection shall be made with a UL listed ring lug.

•

The drive is installed into a separate electrical type 1 enclosure or better, as defined by UL50.

•

UL listed class CC acting fuses e.g. Bussman Limitron KTK series, Gould AmpTrap ATM series
or equivalent are used in the AC supply.

•

Ensure that the field wiring leads are securely installed to the input and output power tabs.

•

Power circuit wiring leads need to be a minimum of 14 AWG wire.

7.1.2

AC supply specification

The drive is suitable for use on available circuits of 5,000A RMS maximum, 480V/240V maximum,
when protected by fuses only, sized 250% FLA maximum.

7.1.3

Motor overload protection

The drive provides motor overload protection. The overload protection level is 110% of the full load
current. For individual motor drive current rating, please refer relevant section of the User guide.

7.1.4

Over-speed protection

The drive provides over-speed protection. However, it does not provide the level of protection
afforded by an independent high integrity over-speed protection device.

«
...
19
20
21
22
»

Содержание VFD66JCB-1























Отзывы:

Нет отзывов