manualshive.com logo in svg

Johnson Controls tyco PG8WLSHW8, Руководство по установке, Страница: 14 / 42

Поделиться
Скачать
Johnson Controls tyco PG8WLSHW8 Скачать руководство пользователя страница 14

The following figure shows the different wiring configurations for SEOL resistors. The image on the

left shows one normally closed contact with an SEOL resistor, and the image on the right shows one

normally open contact with an SEOL resistor.

Note: 

SEOL resistors can have a resistance between 1 kΩ and 10 kΩ. You must install the

SEOL resistor at the end of the loop. UL and ULC verified functionality only with a 5.6 kΩ SEOL

resistor.

For ULC Security Level I burglary installations, use the wiring configurations in Figure 4.
For fire detection installations that use smoke detectors, powered or non-powered heat detectors,

or CO detectors, use the wiring configuration on the right hand side of Figure 4. These devices

use separate AUX2 output for power. Make sure that the voltage range of the AUX2 output is

compatible with the input voltage range of the detector you are using.

Figure 4: SEOL wiring

Callout

Description

1

Zone terminal

2

COM terminal

3

Normally open contact

4

End-of-line resistor

5

Normally closed contact

Note: 

Do not exceed a wire resistance of 100 Ω. For more information, see Table 4.

The following table shows the zone status for a given resistance value.

PG8WLSHW8 and PG9WLSHW8 IQ Hardwire PowerG Wired to Wireless Converter Installation Manual

14

Содержание tyco PG8WLSHW8











































Отзывы:

Нет отзывов