manualshive.com logo in svg

Johnson Controls LIT-12011302, Руководство по установке, Страница: 9 / 9

Поделиться
Скачать
Johnson Controls LIT-12011302 Скачать руководство пользователя страница 9

Published in U.S.A.

www.johnsoncontrols.com

LN Series LN-VSTAT and LN-PSTAT Sensors Installation Instructions

 9

Controls Group

507 E. Michigan Street
Milwaukee, WI  53202

Metasys® is a registered trademark of Johnson Controls, Inc.

All other marks herein are the marks of their respective owners.

© 2007 Johnson Controls, Inc.

For additional information and detailed explanations on 
network topology and wire length restrictions, refer to 
Echelon Corporation’s 

Junction Box and Wiring 

Guideline for Twisted Pair L

ON

W

ORKS

 Networks 

(Part # 005-0023-01).

Note:

Use proper network terminators depending on 

the type of network topology used. Failure to do so may 
result in communication errors between controllers. Do 
not use multiple gauges of cable on the same 
communication bus, as this may also result in 
communication errors.

Troubleshooting

Table 1:  Troubleshooting

Problem

Possible Cause

Solution

Temperature is not read 
properly

Wrong connection

Verify that every connection is properly wired.

Temperature setpoint is not 
read properly

Wrong connection

Verify that every connection is properly wired.

Software configuration

Verify that the setpoint is configured correctly according to 
the selected sensor model.

Содержание LIT-12011302










Отзывы:

Нет отзывов