Johnson Controls Kantech tyco ioSmart Скачать руководство пользователя страница 43

Страница: 43 / 46

Configuring the reader using a Kantech smartcard

About this task:

As an alternative method to using the terminal block to short together two or more outputs, you

can configure the reader using a Kantech smartcard.

You can configure up to eight different modes. The following steps describe how to configure the

first two modes. For other modes, follow the same steps, but substitute the appropriate values

from Table 22.

1. Reset the reader to factory default mode and present the card within the first 10 seconds.

Maintain contact for at least 4 seconds. The reader beeps once and the LED flashes once.

Optional:

To configure Wiegand 34-bit format transmission, present the card to the reader

once. Five seconds later, the reader beeps once and the LED flashes once to confirm mode 1.

Optional:

To configure Wiegand 26-bit format transmission, present the card to the reader

twice. Five seconds after the last card presentation, the reader beeps twice and the LED

flashes twice to confirm mode 2.

4. Present the card one final time to confirm the configuration. The reader acknowledges the

new configuration with a 1-second continuous beep and LED activation.

The following table outlines the amount of card presentations that are required for each

mode.

Table 22: Card configuration modes

Mode

Card presentations

Functions

Once

34-bit Wiegand transmission

Twice

26-bit Wiegand transmission

Three times

XSF transmission format

Four times

SSF transmission format

Five times

Send UID only

Six times

14443 Type B enabled

Seven times

HID Prox disabled

Eight times

Enable Wiegand mode tamper reporting

Note:

*Configuration mode 8 is supported for firmware 1.04 and higher. Wiegand mode

tamper reporting is configured by default for firmware 1.03 and lower.

Note:

If you select a nonexistent mode, the error mode is triggered; this is a 4-second

sequence of beeps and a flashing LED.

After the configuration is confirmed, the reader can accept another configuration within 10

seconds. If you want to use the card to reconfigure the reader, return the reader to factory default

mode.

ioSmart Card Reader Installation Guide

Содержание Kantech tyco ioSmart













































Результаты поиска

Содержание Kantech tyco ioSmart

Отзывы:

Бренды по названию

Популярные бренды

Johnson Controls Kantech tyco ioSmart, Руководство по установке

Результаты поиска

Содержание Kantech tyco ioSmart

Отзывы:

Бренды по названию

Популярные бренды