Johnson Controls J ZT Series Скачать руководство пользователя | Manualshive

Страница: 3 / 66

background image

5370597-JIM-D-1019

Johnson Controls Ducted Systems

3

Inspection

As soon as a unit is received, it should be inspected for possible
damage during transit. If damage is evident, the extent of the
damage should be noted on the carrier’s freight bill. A separate
request for inspection by the carrier’s agent should be made in
writing.

Reference

Additional information is available in the following reference
forms:

• Technical Guide - JA3 thru JA5ZT, 5167823
• General Installation - JA3 thru JA5ZT, 5167545
• Smart Equipment™ Control Quick Start Guide - 1136326
• Economizer Accessory -

Downflow Factory Installed
Downflow Field Installed
Horizontal Field Installed

• Motorized Outdoor Air Damper
• Manual Outdoor Air Damper (0-100%)
• Manual Outdoor Air Damper (0-35%)
• Gas Heat Propane Conversion Kit
• Gas Heat High Altitude Kit (Natural Gas)
• Gas Heat High Altitude Kit (Propane)
• –60



F Gas Heat Kit

• Electric Heater Accessory

Renewal Parts

For authorized replacement parts call Johnson Controls, Inc.
National Source 1 Parts outlet 1-866-523-9670.

Approvals

Design certified by CSA as follows:
1.

For use as a cooling only unit, cooling unit with
supplemental electric heat or a forced air furnace.

2.

For outdoor installation only.

3.

For installation on combustible material and may be
installed directly on combustible flooring or, in the U.S., on
wood flooring or Class A, Class B or Class C roof covering
materials.

4.

For use with natural gas (convertible to LP with kit).

This product must be installed in strict compliance with
the enclosed installation instructions and any applicable
local, state and national codes including, but not limited
to, building, electrical, and mechanical codes.
The furnace and its individual shut-off valve must be
disconnected from the gas supply piping system during
any pressure testing at pressures in excess of 1/2 PSIG.
Pressures greater than 1/2 PSIG will cause gas valve
damage resulting in a hazardous condition. If it is
subjected to a pressure greater than 1/2 PSIG, the gas
valve must be replaced.
The furnace must be isolated from the gas supply piping
system by closing its individual manual shut-off valve
during any pressure testing of the gas supply piping
system at test pressures equal to or less than 1/2 PSIG

This product must be installed in strict compliance with
the enclosed installation instructions and any applicable
local, state, and national codes including, but not limited
to, building, electrical, and mechanical codes.

Improper installation may create a condition where the
operation of the product could cause personal injury or
property damage.

This system uses R-410A Refrigerant which operates at
higher pressures than R-22. No other refrigerant may be
used in this system.

«
1
2
3
4
5
...
»

Содержание J ZT Series



































































Отзывы:

Нет отзывов

Похожие инструкции для J ZT Series

Бренд: Olimpia splendid Страницы: 24

Бренд: Midea Страницы: 15

Бренд: Bryant Страницы: 32

Бренд: Viking Страницы: 2

Бренд: Altech Страницы: 48

ELFOFresh2 CPAN-U 70-120 Series

Бренд: CLIVET Страницы: 72

Бренд: Olimpia splendid Страницы: 270

SCE-AC13650B460V3

Бренд: SCE Страницы: 17

Бренд: Kooltronic Страницы: 13

Бренд: MANN+HUMMEL Страницы: 31

Бренд: McQuay Страницы: 65

Бренд: Daikin Страницы: 15

Бренд: Lennox Страницы: 8

Бренд: Samsung Страницы: 124

AJ NBLDCH Series

Бренд: Samsung Страницы: 41

AJ NCJ2EG Series

Бренд: Samsung Страницы: 38

AJ CXS CH Series

Бренд: Samsung Страницы: 36

Бренд: Samsung Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды